Fellowes 125i Manual - Page 2

I. A. B. G. K. C. ENGLISH Model C-120i/C-120Ci KEY D. A. SafeSense® Technology F. Basket (CD) K. Control Panel and LEDs B. Paper entry G. See safety instructions 1. Reverse 6. Remove paper C. CD entry H. Casters (2) 2. ON/OFF 7. Overheat D. Door I. Disconnect power switch 3. Forward 8. Sheet capacity indicator E. Basket (paper) H. J. Shipping bolts (wing nuts) To be removed prior to operation 4. Bin full 5. Door open 9. SafeSense® indicator (yellow) 10. Auto button CAPABILITIES Will shred: Paper, credit cards, CD/DVD's, staples and small paper clips Will not shred: Adhesive labels, continuous form paper, transparencies, newspaper, cardboard, large paper clips, laminates, file folders, X-rays or plastic other than noted above Paper shred size: Cross-Cut 5/32 inches x 1-1/2 inches (3.9mm x 38mm) Strip Cut 7/32 inches (5.8mm) Advanced product features Maximum: Sheets per pass...18* CDs/Cards per pass...1* Paper entry width 9 inches (230mm) *8.5 inches x11 inches, 20lb., (75g) paper at 120V, 60 Hz, C-120i 6 Amps, C-120Ci 8 Amps; heavier paper, humidity or other than rated voltage may reduce capacity. Recommended daily usage rates: 100-150 paper passes; 100 cards; 10 CDs Fellowes SafeSense® shredders are designed to be operated in office environments ranging between 50 - 80 degrees Fahrenheit (10 - 26 degrees Celsius) and 40 - 80% relative humidity. Jam Proof System Eliminates frustrating jams by preventing overloads and powering through misfed paper Patented SafeSense® Technology Stops shredder immediately when hands are too close to the paper entry IMPORTANT SAFETY INSTRUCTIONS - Read Before Using! Sleep Mode Energy saving feature shuts down automatically after 2 minutes of no shredding activity • Keep away from children and pets. Keep hands away from paper entry. Always set to off or unplug when not in use. • Keep foreign objects - gloves, jewelry, clothing, hair, etc. - away from shredder openings. If object enters top opening, switch to 15 Reverse ( ) to back out object. • Never use aerosol products, petroleum based lubricants or other flammable 15 products on or near shredder. Do not use canned air on shredder. • Do not use if damaged or defective. Do not disassemble shredder. Do not place near or over heat source or water. 15 • This shredder has a Disconnect Power Switch (I) that must be in the ON (I) position to operate shredder. In case of emergency, move switch to OFF (O) position. This action will stop shredder immediately. INSTALLATION INSTRUCTIONS • Avoid touching exposed cutting blades under shredder head. • Keep finger away from CD hole when shredding. • Do not put foreign objects in paper entry. • The grounded socket-outlet shall be installed near the equipment and shall be easily accessible. • WARNING: Shredder Stability - Secure Shredder to wall with hardware provided following the instructions under Installation Instructions • Product is intended for commercial use only, and not for use around children. 1. Place shredder against the wall (drywall, wooden, or concrete). Mark screw locations on wall through back of cabinet. 2. Drill 1/4" hole in wall for the anchor plugs. 3. Insert white plastic anchor plugs into drilled holes. 4. Insert (2) screws through back of cabinet and thread black rubber spacer onto the screw. 5. From inside cabinet use Phillips screw driver to secure shredder to the wall. 2 BASIC SHREDDING OPERATION PAPER/CARD OR CD 1 2 3 4 5 6 77 AUTO Continuous operation: 45 minutes maximum NOTE: Continuous operation beyond 45 minutes will trigger Plug in and put disconnect power switch in ON (I) position Press ( ) ON to activate Feed paper/card straight into paper entry and release To shred CDs rotate CD flap into place 45 minute cool down period. www.fellowes.com features an extensive on-line support section with a number of self-service options AUTO Hold CD at edge, When finished feed into CD shredding set entry and release to OFF ( ) JAM PROOF SYSTEM OPERATION* Eliminates frustrating jams by preventing overloads and powering through misfed paper. Do nothing and or shredder will go automatically to sleep mode 1 Advanced Jam Prevention- Electronically measures paper thickness to prevent paper jams: Up to RED: Too Many sheets have been inserted. Up to YELLOW: Productivity is optimized. 2 Remove several sheets until indicator is below red. 3 Continue 100% Jam Proof Shredding Up to GREEN: More sheets can be added. If a misfeed occurs: All indicators light up and shredder pauses for 3-6 seconds *100% Jam Proof when used in accordance with user manual SLEEP MODE WHEN IN SLEEP MODE 1 2 3 Wait for flashing to stop after automatic correction is complete. Regular shredding will resume. If illuminates after paper has been reversed, press reverse and remove paper. Otherwise, regular shredding will resume. SAFESENSE® TECHNOLOGY OPERATION SET-UP AND TESTING 1 2 3 AUTO AUTO In sleep mode To get out of sleep mode or insert paper touch control panel Turn the shredder ON ( ) to activate SafeSense® Touch test area and look for the SafeSense® indicator to illuminate SafeSense® is active and working properly PREVENTIVE MAINTENANCE AND MISCELLANEOUS TROUBLESHOOTING • For peak performance, we recommend oiling shredder each time waste bin is emptied. Only use a non-aerosol vegetable oil. Machines not oiled may lose sheet capacity, become noisy, and ultimately, stop running. • Though paper detection sensors are designed to be maintenance free, the sensors occasionally become blocked by paper dust, causing the motor to run even if there is no paper present. Both sensors are located in the center of the paper entry. • Self Cleaning Cycle: Shredder periodically cycles in forward and reverse lasting 3-6 seconds. • Empty wastebasket when bin full indicator lights up. • Shredder won't run if the door is open, or bin needs to be emptied. • Maintenance is an important part of protecting your investment. Don't forget our oil (35250) and shredder bags (36054). • When shredding for a prolonged period of time, the motor can become warm and require a cool down period. When this occurs the overheat indicator will alert you to the problem, this model will require 45 minutes to cool down. Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers. 3