Fellowes 225Ci Manual - Page 4

Cleaning Auto-start Infrared Sensors, Oiling Shredder - cross cut shredder

Get Fellowes 225Ci PDF manuals and user guides View all Fellowes 225Ci manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

ENGLISH Models 225Ci/225i PRODUCT MAINTENANCE Cleaning Auto-Start Infrared Sensors Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present (Note: two paper detection sensors are located in the center of the paper entry). TO CLEAN THE SENSORS 1 AUTO 2 C-225 3 AUTO 4 C -2 2 5 AUTO Turn off and unplug shredder Locate Auto-start infared sensor Dip cotton swab in rubbing alcohol Using cotton swab, wipe away any contamination from the paper sensors OILING SHREDDER All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin. FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE 1 2 C-225 AUTO AUTO *Apply oil across entry Press and hold forward ( ) 2-3 seconds *Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250 TPRROEVUEBNLETSIVHEOMOTAIINNGTENANCE & ACCESSORIES A B C D 15 A. Door Open Indicator: The shredder will not run if the cabinet door is open. When illuminated, close the door to resume shredding. B. Bin Full Indicator: When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes waste bag 36054. C. Remove Paper Indicator: When illuminated, press reverse ( ) and remove paper. Reduce paper quantity to an acceptable amount and refeed into paper entry. D. SafeSense® Indicator: If hands are too close to the paper entry, the SafeSense® indicator will illuminate and the shredder will stop shredding. If SafeSense® is active for 3 seconds, the shredder will automatically turn off and the user must press the power button on the control panel to resume shredding. Self Cleaning Cycle: Shredder periodically cycles in forward and reverse lasting 3-6 seconds (225Ci only). Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers. 4

  • 1
  • 2
  • 3
  • 4
  • 5
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
CLEANING AUTO-START INFRARED SENSORS
PRODUCT MAINTENANCE
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run
even if there is no paper present
(Note: two paper detection sensors are located in the center of the paper entry)
.
TO CLEAN THE SENSORS
Turn off and unplug
shredder
Locate Auto-start
infared sensor
Using cotton swab, wipe
away any contamination
from the paper sensors
Dip cotton swab in
rubbing alcohol
AUTO
1
ENGLISH
Models 225Ci/225i
All cross-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive
noise when shredding and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you
empty your waste bin.
OILING SHREDDER
*Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
*Apply oil across entry
TROUBLESHOOTING
4
Press and hold forward
(
) 2-3 seconds
AUTO
2
A
B
C
D
A. Door Open Indicator:
The shredder will not run if the cabinet door is open. When illuminated, close the
door to resume shredding.
B. Bin Full Indicator:
When illuminated, the shredder waste bin is full and needs to be emptied. Use Fellowes
waste bag 36054.
C. Remove Paper Indicator:
When illuminated, press reverse (
) and remove paper.
Reduce paper quantity to an acceptable amount and refeed into paper entry.
D. SafeSense
®
Indicator:
I
f hands are too close to the paper entry, the SafeSense
®
indicator will illuminate
and the shredder will stop shredding.
If SafeSense
®
is active for 3 seconds, the shredder will automatically
turn off and the user must press the power button on the control panel to resume shredding.
Self Cleaning
Cycle:
Shredder periodically cycles in forward and reverse lasting 3-6 seconds (225Ci only).
3
2
4
1