Fender 115 PRO Owners Manual - Page 6

6 Fender® 115 Pro Loudspeaker Enclosure Your new 115 Pro Bass Loudspeaker Enclosure is constructed from 3/4" (1.9 cm) 13-ply Baltic Birch Plywood and is capable of handling 350 Watts of continuous power. The 115 Pro features a 15" (38.1 cm) speaker with 105 oz (2.98 kg) magnet and is designed for use with Fender® Bassman® and Pro Series amplifiers or other professional quality bass amplifiers. Please read these instructions and the instructions that came with your amplifier before making connections. Follow all equipment caution and safety labeling. SPEAKER CONNECTIONS Use 16 gauge (or heavier) speaker cable with one of the three types of input connections on your 115 Pro: A) Phone jacks with a standard 1/4" plug B) Binding posts with dual "banana" plug or stripped wires C) Speakon® connector with Speakon® plug Multiple 115 Pro cabinets can be linked as illustrated, when additional output is needed. Note: Follow the speaker impedance load guidelines set by the manufacturer of your amplifier to avoid damage to your equipment. SERIAL NUMBER POWER RATING 350W CONTINUOUS 700W PROGRAM HORN LEVEL MODEL WARNING: FENDER LOUDSPEAKER SYSTEMS ARE CAPABLE OF PRODUCING VERY HIGH SOUND PRESSURE LEVELS WHICH MAY CAUSE TEMPORARY OR PERMANENT HEARING DAMAGE. USE CARE WHEN SETTING AND ADJUSTING VOLUME LEVELS DURING USE. A PRODUCT OF: FENDER MUSICAL INSTRUMENTS CORP., CORONA, CA U.S.A. MADE IN MEXICO MIN. MAX. PARALLEL INPUTS IMPEDANCE 8Ω SERIAL NUMBER POWER RATING 350W CONTINUOUS 700W PROGRAM HORN LEVEL MODEL WARNING: FENDER LOUDSPEAKER SYSTEMS ARE CAPABLE OF PRODUCING VERY HIGH SOUND PRESSURE LEVELS WHICH MAY CAUSE TEMPORARY OR PERMANENT HEARING DAMAGE. USE CARE WHEN SETTING AND ADJUSTING VOLUME LEVELS DURING USE. A PRODUCT OF: FENDER MUSICAL INSTRUMENTS CORP., CORONA, CA U.S.A. MADE IN MEXICO MIN. MAX. PARALLEL INPUTS IMPEDANCE 8Ω HORN TWEETER The horn tweeter is protected from power-overload damage by an incandescent lamp. If the horn tweeter stops responding, replace the lamp as you would a blown fuse. The lamp and a spare (reorder P/N 051857) are located on the circuit board on the inside of the input jack panel. Lamp Replacement: 1) Remove the 4 screws from the input jack panel corners. 2) Pull the panel out, then up. 3) Use a small flathead screwdriver to remove the blown lamp which is visible through a cutout in the circuit board. 4) Remove the spare lamp stowed on the side of the circuit board and install it where the blown lamp was located. 5) Install the input jack plate in the reverse order of removal. SPECIFICATIONS PART NUMBER: 22-17700-000 DRIVERS: One 15" (38.1 cm) Fender Special Design Cast Frame Woofer 3" (7.6 cm) Voice Coil, 105 oz (2.98 kg) Magnet One Horn Tweeter 1" (2.5 cm) Voice Coil, 8 oz (0.23 kg) Magnet CABINET: 3/4" (1.9 cm) 13-ply Baltic Birch Plywood SENSITIVITY: 97.5 dB, 1 Watt - 1 Meter POWER HANDLING: 350 Watts, Continuous 700 Watts, Program IMPEDANCE: 8Ω CONNECTIONS: Dual, Parallel Wired, 1/4" High Current Input Jacks, Binding Posts and Speakon® Connector ENCLOSURE VOLUME: VB = 3.4 ft3 (97 l) DIMENSIONS: Height: 18.5 in (47.0 cm) Width: 25.5 in (64.8 cm) Depth: 18.5 in (47.0 cm) WEIGHT: 64 lb (29.1 kg) Product specifications are subject to change without notice. A PRODUCT OF: FENDER MUSICAL INSTRUMENTS CORP. CORONA, CA USA Fender® is a registered trademark of FMIC, Speakon® is a registered trademark of Neutrik. Copyright © 2003 FMIC www.f e n d e r.com ✧ www. m r g e a r h e a d .net