Fender 65 Super Reverb Owners Manual - Page 5

Specifications - amp

Get Fender 65 Super Reverb PDF manuals and user guides View all Fender 65 Super Reverb manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

    ¶   6 8 3 ( 5 5 ( 9 ( 5 R. IEC POWER SOCKET - The line cord must be connected to a grounded AC receptacle in accordance with the voltage and frequency ratings as specified on the rear panel of the unit. S. FUSE - Replace a blown fuse only with a fuse of the type and rating as specified on the rear panel of the unit. If the amp repeatedly blows fuses, have the unit tested by an authorized Fender service technician. T. POWER - Switches the unit ON and OFF. U. STANDBY - In standby mode, power is supplied only to the tube filaments to keep them warm and ready to operate. Use standby during short breaks to eliminate warm-up time and extend the life of the tubes. V. MAIN SPEAKER JACK - This is the primary speaker connection. Speakers (internal or external) must always be connected here while operating the unit. W. EXTERNAL SPEAKER JACK - Plug in external speakers here. This jack is wired in parallel with the main speaker jack. *** NOTE: The amp is optimized for a 2 ohm speaker load, which is the rating of the internal speaker configuration. If a speaker load other than 2 ohms is used, the amplifier will distort before reaching maximum output, and the life of the tubes will be reduced. Two external 4 ohm speaker cabinets would provide the recommended 2 ohm load. X. FOOTSWITCH - Plug the included footswitch in here. The footswitch enables on/off switching of the vibrato and reverb effects. *** NOTE: Vibrato will NOT work without the footswitch connected, but the reverb effect will. Y. REVERB OUTPUT / INPUT - RCA jack connections for routing the reverb signal to and from the reverb pan. Specifications: TYPE: PART NUMBERS: POWER REQUIREMENTS: FUSE TYPE IM P E D A N C E S SPEAKER COMPLEMENT: D IM E N S IO N S W EIGHT: 120V models: 230-240V models: 100V models: Inputs 1: Inputs 2: O utput: Height: W idth: Depth: PR 469 021-7600-000, 120V, 60Hz (USA), 021-7660-000, 230V, 50Hz (Europe), 021-7640-000, 230V, 50Hz (UK), 021-7630-000, 240V, 50Hz (Aust), 021-7670-000, 100V, 50-60Hz (Japan) 270W 3A, fast-blow, 125V minimum, 1. 6A, fast-blow, 250V minimum, 3A, fast-blow, 125V minimum 1M ohms (both channels) 136K ohms (both channels) 2 ohms Four 10 in. (25.4 cm) vintage reissue, P/N 055613 24 7/8 in. (63. 2 cm) 25 1/8 in. (63. 8 cm) 10 1/2 in. (26. 7 cm) 65 lbs. (24. 3 kg) Product Specifications are subject to change without notice. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
±² ± ² ± ² ± ²±²±² ±
±¶³´±683(5±5(9(5%±
±² ± ² ± ² ± ²±²±²±²±²
5
R. IEC POWER SOCKET - The line cord must be
connected to a grounded AC receptacle in accor-
dance with the voltage and frequency ratings as
specified on the rear panel of the unit.
S.
FUSE - Replace a blown fuse only with a fuse of
the type and rating as specified on the rear panel
of the unit.
If the amp repeatedly blows fuses,
have the unit tested by an authorized Fender
service technician.
T.
POWER - Switches the unit ON and OFF.
U. STANDBY - In standby mode, power is supplied
only to the tube filaments to keep them warm and
ready to operate.
Use standby during short
breaks to eliminate warm-up time and extend the
life of the tubes.
V. MAIN SPEAKER JACK - This is the primary
speaker connection.
Speakers (internal or
external) must always be connected here while
operating the unit.
W. EXTERNAL SPEAKER JACK - Plug in external
speakers here.
This jack is wired in parallel with
the main speaker jack.
***
NOTE: The amp is optimized for a 2 ohm
speaker load, which is the rating of the
internal speaker configuration.
If a speaker
load other than 2 ohms is used, the amplifier
will distort before reaching maximum output,
and the life of the tubes will be reduced.
Two
external 4 ohm speaker cabinets would
provide the recommended 2 ohm load.
X. FOOTSWITCH - Plug the included footswitch in
here.
The footswitch enables on/off switching of
the vibrato and reverb effects.
***
NOTE:
Vibrato will NOT work without the
footswitch connected, but the reverb effect
will.
Y.
REVERB OUTPUT / INPUT - RCA jack connec-
tions for routing the reverb signal to and from the
reverb pan.
Specifications:
TYPE:
PR 469
PART NUMBERS:
021-7600-000, 120V, 60Hz (USA),
021-7660-000, 230V, 50Hz (Europe),
021-7640-000, 230V, 50Hz (UK),
021-7630-000, 240V, 50Hz (Aust),
021-7670-000, 100V, 50-60Hz (Japan)
POWER REQUIREMENTS:
270W
FUSE TYPE
120V models:
3A, fast-blow, 125V minimum,
230-240V models:
1. 6A, fast-blow, 250V minimum,
100V models:
3A, fast-blow, 125V minimum
IMPEDANCES
Inputs 1:
1M ohms (both channels)
Inputs 2:
136K ohms (both channels)
Output:
2 ohms
SPEAKER COMPLEMENT:
Four 10 in. (25.4 cm)
vintage reissue, P/N 055613
DIMENSIONS
Height:
24 7/8 in.
(63. 2 cm)
Width:
25 1/8 in.
(63. 8 cm)
Depth:
10 1/2 in.
(26. 7 cm)
WEIGHT:
65 lbs.
(24. 3 kg)
Product Specifications are subject to change without notice.