Fender EC Vibro-Champ Owners Manual - Page 7
Specifications - speaker
View all Fender EC Vibro-Champ manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Chassis Bottom View Rear of Amplifier 5 6 Y V 3 6 GT GT 12 12 A A X X 7 7 Tube Locations G. POWER CORD - Connect to a grounded outlet in accordance with the voltage and frequency specifications shown on the amplifier information label. ♫ The amplifier information label is located inside the amplifier cabinet on the left-hand side, when viewed from the rear of the amplifier. H. FUSE - Protects the amplifier from electrical faults. Replace a blown fuse only with the type and rating specified on the amplifier information label. I. SPEAKER JACK - Connection for the internal speaker or for a 4Ω external speaker cabinet. ! A speaker must ALWAYS be connected to the SPEAKER JACK when the amplifier is ON or damage may occur to the unit. Switch the amplifier OFF while changing speaker connections. J. FOOTSWITCH JACK - Plug the optional footswitch in here to enable remote on-off switching of the Vibrato effect. K. FENDER® GROOVE TUBES® - Your new Fender amplifier comes equipped with the highest quality tubes available sourced from various manufacturers worldwide. Because of occasional irregularities in supply, the specific tube type used in each amplifier is subject to change without notice. When replacing output tubes, please note the specific tube markings on the original tubes factory supplied with your amplifier. For example, 6V6 output tube types used by Fender include, but are not limited to: 6V6C; 6V6CQ; 6V6RD; etc. The installation of a different type may require significant adjustment by a qualified technician to avoid a reduction in amplifier performance and tube life span. Additionally, Fender Groove Tubes tests and sorts many of our output tubes based on their measured performance. The sorted tubes are labeled with a fine rating of 1-10 and may also be labeled with a coarse rating color of BLUE, WHITE or RED. A pair of matched output tubes with the same fine rating (and coarse rating, if applicable) as the original tubes will be the perfect replacement. However, replacement tubes with a fine rating within one number of the original tubes can be used without re-biasing the amplifier. If you have questions or concerns, please contact your Fender dealer or authorized service center. TYPE: PART NUMBERS: POWER: INPUT IMPEDANCE: SPEAKER: TUBES: FUSE: ACCESSORIES: DIMENSIONS: Specifications PR 1171 8161500000 (120V, 60Hz) 8161505000 (220V, 50Hz) ARG 8161501000 (110V, 60Hz) TW 8161506000 (230V, 50Hz) EUR 8161503000 (240V, 50Hz) AUS 8161507000 (100V, 50/60Hz) JPN 8161504000 (230V, 50Hz) UK 8161509000 (220V, 60Hz) ROK REQUIREMENTS: 60W OUTPUT: 5W RMS into 4Ω @ 10% THD, 1kHz INPUT 1: 1MΩ INPUT 2: 136kΩ One 4Ω, 8" Weber with AlNiCo magnet (P/N: 0077212000) One 6V6GT (P/N: 0023564000); One 5Y3GT (P/N: 0023614000); Two 12AX7 (P/N: 0013341000) 100V-120V VERSIONS: F 1.25A L, 250V 220V-240V VERSIONS: F 1A L, 250V FOOTSWITCH (OPTIONAL): 1-button, Vibrato on-off (P/N: 0994049000) DUST COVER (INCLUDED): (P/N: 0077214000) HEIGHT: 13.5 in (34.3 cm) WIDTH: 12.5 in (31.8 cm) DEPTH: 7.8 in (19.8 cm) WEIGHT: 16.5 lb (7.5 kg) Product specifications are subject to change without notice. f e n d e r. c o m 7