Fisher and Paykel DE70FA1 DE08/09 DE70 Electric Dryer Install (English)
Fisher and Paykel DE70FA1 Manual
 |
View all Fisher and Paykel DE70FA1 manuals
Add to My Manuals
Save this manual to your list of manuals |
Fisher and Paykel DE70FA1 manual content summary:
- Fisher and Paykel DE70FA1 | DE08/09 DE70 Electric Dryer Install (English) - Page 1
Be sure to leave these instructions with the Consumer. Note to Consumer - Keep these instructions with your Owner's Manual for future reference. A the dryer to the outdoors is strongly recommended to prevent large amounts of moisture and lint from being blown into the room. • Service information - Fisher and Paykel DE70FA1 | DE08/09 DE70 Electric Dryer Install (English) - Page 2
208V or 240V installation 30 amps. • If the electric supply does not meet the above specifications, call a licensed electrician. GROUNDED. Grounding instructions Dryer must be electrically grounded in accordance with local codes and ordinances, or in the absence of local codes, in accordance with - Fisher and Paykel DE70FA1 | DE08/09 DE70 Electric Dryer Install (English) - Page 3
-4 TAB OPENING -- 4 8 1/2" 4 3/4" Only metal duct may be used inside the dryer cabinet 11 1/4" MEM 01, 4 3/4" NOTE: To secure the duct, insert the tab ( . The male end of each section of duct must point away from the dryer. • Do not assemble the duct work with fasteners that extend into the duct - Fisher and Paykel DE70FA1 | DE08/09 DE70 Electric Dryer Install (English) - Page 4
and Safety Standard, Title 24 CFR, Part 32-80. • The dryer must be exhausted to the outdoors with the termination securely fastened to the MUST BE METAL. • For Electrical Connections see "CONNECTING DRYER USING 4-WIRE CONNECTIONS". SERVICING: A CAUTION: Consideration must be given to provide - Fisher and Paykel DE70FA1 | DE08/09 DE70 Electric Dryer Install (English) - Page 5
Instructions If all rigid metal duct cannot be used, then flexible all metal venting can be used, but it will reduce the maximum recommended duct length. In special installations when it is impossible to make a connection with the above recommendations, then UL listed clothes dryer clothes dryers is
-
1 -
2 -
3 -
4 -
5
 |
 |
16
Installation
instructions
for
your
new
Electric
Dryer
Before
you
begin
-
Read
these
instructions
completely
and
carefully.
IMPORTANT
-
Save
these
instructions
for
local
inspector's
use.
IMPORTANT
-
OBSERVE
ALL
GOVERNING
CODES
AND
ORDINANCES.
Note
to
Installer
-
Be
sure
to
leave
these
instructions
with
the
Consumer.
Note
to
Consumer
-
Keep
these
instructions
with
your
Owner's
Manual
for
future
reference.
A
WARNING
-
POTENTIAL
FIRE
AND
SHOCK
HAZARD
•
Use
only
rigid
metal
or
flexible
metal
4"
diameter
ductwork
for
exhausting
to
the
outdoors:
Never
use
plastic
or
other
combustible
ductwork.
•
This
appliance
must
be
properly
grounded
and
installed
as
described
in
these
instructions.
•
Do
not
install
or
store
appliance
in
an
area
where
it
will
be
exposed
to
water/weather.
•
The
National
Fuel
Gas
Code
restricts
installations
of
gas
appliances
in
garages.
They
must
be
18"
off
the
ground
and
protected
by
a
barrier
from
vehicles.
Important
•
Exhausting
the
dryer
to
the
outdoors
is
strongly
recommended
to
prevent
large
amounts
of
moisture
and
lint
from
being
blown
into
the
room.
•
Service
information
and
wiring
diagram
located
in
control
console.
Tools
you
will
need
Slip
joint
pliers
Screwdrivers
3/8"
nut
driver
Step
1
Remove
and
save
literature
and
parts
package
from
dryer
drum
Step
2
Lay
carton
corner
posts
or
two
2"x4"
boards
on
fl
oor.
Lay
dryer
on
its
back.
Step
3
Remove
foam
shipping
pads
by
pulling
at
sides
and
breaking
away
from
dryer
legs.
Be
sure
to
remove
all
foam
pieces
from
around
legs.
Step
4
Stand
dryer
upright
Step
5
Move
dryer
to
desired
operating
location.
FOAM
SHIPPING
PADS
Installation
PULL
HERE
TO
SEPARATE
FROM
FRONT
LEG
DRYER
LEGS
PULL
HERE
TO
SEPARATE
FROM
REAR
LEG
Step
6
Adjust
leveling
legs
to
match
washer
height.
Dryer
must
be
level
and
rest
firmly
on
all
four
leveling
legs.
Step
7
Connect
to
power
supply.
(See
ELECTRICAL
CONNECTION
INFORMATION
section
of
this
instruction.)
Step
8
Connect
external
exhaust
or
deflector.
(See
EXHAUST
INFORMATION
section
of
this
instruction.)
Step
9
Check
for
proper
operation.
Step
10
Place
Owner's
manual
and
installation
instructions
in
a
location
where
they
may
be
found
by
the
customer.
500A187P016
Rev.
2
Pub.
No.
31-16001
1