Fisher and Paykel RF170ADUX1 5499_GLO_Surround_Kit_Instructions_FLI (English) - Page 2

8 TRIM INSTALLATION The bottom trim is designed to cover the front edge of the floor base panel of the cabinet. This trim can be installed on a raised toe kick (diagram 1a) or toe kick below the refrigerator (diagram 1b) 16mm (5/8 inch) plywood or MDF board insert Remembering that if this trim is to be used with the refrigerator at floor level the cut out dimensions will need to have 16mm (5/8") added to its height to allow for the bottom trim to be fitted. Note this trim is optional on this Part of base type of installation. If used with a raised toe kick the 16mm packer should be part of the base (diagram 5). Therefore 16mm is not required to be added to the height dimension. 1. If used place the 16mm (5/8") piece of plywood or with bottom trim fitted into the cavity (diagram 5 or 6). Note the piece should be the same size as the base of the cavity. 2. Remove protective coating film from surround trim. 3. To install the surrounds, first clip in the top surround. Ensure the locator strips at the rear of the top brackets clip into the rear of the top trim. 4. Clip both side trims into place starting from the front cabinet edge. Diagram 5 9 MOVE INTO CAVITY If installing two refrigerators/ freezers side by side a joiner kit is required. Refer to these instructions and fit joiner kit before pushing refrigerator into place, see diagram 6. Plug refrigerator into electrical socket, run water connection to refrigerator if required (Ice & Water models only). Gently install refrigerator into cabinetry making sure it is centred within the surround trim. The front of the refrigerator door should be flush with the front of the cabinetry to obtain an integrated look. Ensure the front leveling feet are adjusted to take the load of the fridge and keep it in place. Optional Diagram 6 10 Kit part numbers and cut out dimensions table 1 x 635 (25") LH Refrigerator Model 807 Kit Part Numbers Brushed Iridium Stainless Stainless Plus Joiner Kit 821351 821361 Cut Out Dimensions Width Depth Height A B* C** 807mm 700mm 1790mm 31 13⁄16" 27 9/16" 70 1/2" 1 x 790 (31 1/8") LH Refrigerator Model 962 Kit Part Numbers Brushed Iridium Stainless Stainless Plus Joiner Kit 821357 821367 Cut Out Dimensions Width A Depth B* Height C** 962mm 700mm 1790mm 37 7/8" 27 9/16" 70 1/2" 635 790 1790 1790 1 x 635 807 (25") RH 635 821352 821362 807mm 700mm 1790mm 1 x 790 962 31 13⁄16" 27 9/16" 70 1/2" (31 1/8") RH 790 821358 821368 962mm 700mm 1790mm 37 7/8" 27 9/16" 70 1/2" 1790 1790 2 x 635 1467 (25") 635 635 821353 821363 819264 1467mm 700mm 1790mm 2 x 790 1777 57 3/4" 27 9/16" 70 1/2" (31 1/8") 790 790 821359 821369 819264 1777mm 700mm 1790mm 70" 27 9/16" 70 1/2" 1790 1790 1 x 680 852 (26 3/4") LH 680 1790 821354 821364 852mm 700mm 1790mm 1 x 900 1072 33 9⁄16" 27 9/16" 70 1/2" (35 7/16") 900 821360 821370 1072mm 700mm 1875mm 42 ¼" 27 9/16" 73 13/16" 1875 1 x 680 852 (26 3/4") RH 680 821355 821365 852mm 700mm 1790mm 1 x 790 962 33 9⁄16" 27 9/16" 70 1/2" (31 1/8") 790 837315 837316 962mm 700mm 1790mm 37 7/8" 27 9/16" 70 1/2" 1790 1790 2 x 680 1557 (26 3/4") 680 680 1790 821356 821366 819264 1557mm 700mm 1790mm 61 5/16" 27 9/16" 70 1/2" * Depth is a minimum requirement ** Height is without 16mm MDF packer *** For refrigerators / freezers where the hinge is not concealed by the door refer to spare parts for the correct kit number. 820413 D should list non concealed number kit. Concealed Hinge Non Concealed Hinge Before you call for service or assistance ... Check the things you can do yourself. Refer to the installation instructions, your User Guide - in particular the troubleshooting section and check that: 1 your product is correctly installed. 2 you are familiar with its normal operation. If after checking these points you still need assistance or parts, use the link at www.fisherpaykel.com for regional service providers. 821996 B NZ AU GB AE HK SG IE US CA EU CN IN 08.12