Fisher and Paykel WL37T26KW2 AquaSmart LED models Installation Instructions &a - Page 32

Out-of-Balance recovery routine, Reset Back to Factory Settings

Get Fisher and Paykel WL37T26KW2 PDF manuals and user guides View all Fisher and Paykel WL37T26KW2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

30 Changing pre-set options Out-of-Balance recovery routine When your AquaSmart™ is spinning it can sense if the wash load is out-of-balance and will stop and re-try spinning up to 3 times. If it still senses an unbalanced load there are two options the machine can take. SOAK light on = automatic recovery Automatic Recovery option Your AquaSmart™ will try to automatically correct the out-of-balance load. It will fill with water and agitate to redistribute the load before trying to spin up again. Machine Stops option Your AquaSmart™ will stop, give a short burst of beeps every 5 seconds, and the spin speed lights will flash. You must redistribute the load more evenly yourself. (Use this option if you wish to conserve water). Your washer arrived with the 'Machine Stops' option set. 1 Enter Options Adjustment mode (refer to page 28). 2 Select SOAK to program your AquaSmart™ to automatically recover. 3 Press POWER to save your selection. SOAK light off =machine stops Fig.21 Adjusting Out-of-Balance recovery routine Reset Back to Factory Settings If you would like to reset all settings back to those that were set when your AquaSmart™ left the factory you have the option of selecting RESET DEFAULTS. 1 Enter Option Adjust Mode (page 28). 2 Press and hold the START /PAUSE button until you hear one quick beep. This indicates that all settings have been returned to the factory default settings. Fig.22 Resetting factory defaults

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
30
Changing pre-set options
Out-of-Balance recovery routine
When your
AquaSmart™
is spinning it can sense if the
wash load is out-of-balance and will stop and re-try
spinning up to 3 times. If it still senses an unbalanced
load there are two options the machine can take.
Automatic Recovery option
Your
AquaSmart™
will try to automatically correct the
out-of-balance load. It will fill with water and agitate
to redistribute the load before trying to spin up again.
Machine Stops option
Your
AquaSmart™
will stop, give a short burst of beeps
every 5 seconds, and the spin speed lights will flash.
You must redistribute the load more evenly yourself.
(Use this option if you wish to conserve water).
Your washer arrived with the ‘Machine Stops’
option set.
1
Enter Options Adjustment mode (refer to page 28).
2
Select SOAK to program your
AquaSmart™
to
automatically recover.
3
Press POWER to save your selection.
Reset Back to Factory Settings
If you would like to reset all settings back to those
that were set when your
AquaSmart™
left the factory
you have the option of selecting RESET DEFAULTS.
1
Enter Option Adjust Mode (page 28).
2
Press and hold the START /PAUSE button until you
hear one quick beep. This indicates that all settings
have been returned to the factory default settings.
SOAK
light on = automatic recovery
SOAK
light off =machine stops
Fig.21 Adjusting Out-of-Balance
recovery routine
Fig.22 Resetting factory defaults