Fluke 753 Fluke 753 754 750 Series Datasheet - Page 11

General specifications Data log function Measure functions: Voltage, current, resistance, frequency, temperature, pressure Reading rate: 1, 2, 5, 10, 20, 30, or 60 readings per minute Maximum record length: 8000 readings (7980 for 30 or 60 readings per minute) Ramp function Source functions: Voltage, current, resistance, frequency, temperature Rate: 4 steps/second Trip detect: Continuity* or voltage *Continuity detection not available when sourcing current Loop power function Voltage: 26 V Accuracy: 10 %, 18 V minimum at 22 mA Maximum current: 25 mA, short-circuit protected Maximum input voltage: 50 V dc Note: 250 Ω series resistance is automatically supplied whenever loop power is enabled on 754. HART modem interface (754 only) Maximum input voltage: 30 V dc Environmental specifications All calibrator specifications apply from +18 °C to +28 °C unless stated otherwise. Operating temperature: -10 °C to 50 °C Storage temperature: -20 °C to 60 °C Operating altitude: 3000 m above mean sea level (9842 ft) 90-day specifications: The standard specification intervals for the 750 Series are 1 and 2 years. Typical 90-day measurement and source accuracy can be estimated by dividing the one year "% of reading" or "% of output" specifications by 2. Floor specifications, expressed as "% of f.s." or "counts" or "ohms" remain constant. Ingress protection: IP-52 Power: Internal battery pack li-ion, 7.2 V, 4400 mAh, 30 Wh Battery life: Typical usage, >8 hours Dimensions: 136mm x 245mm x 63 mm (5.4 in x 9.6 in x 2.5 in) Weight: 1.2 kg (2.7 lb) Side port connections: • Pressure module connector • USB connector to interface to your PC • Digital instrument (HART) connector • Connection for optional battery charger/eliminator Safety: Complies with CAN/CSA C22.2 No 1010.1-92, ANSI/ISA S82.01-1994, UL3111, and EN610-1:1993. Data storage capacity: 1 week of calibration procedures and results Ordering information FLUKE-753 Documenting Process Calibrator FLUKE-754 Documenting Process Calibrator-HART Standard accessories include: Three sets of stackable test leads, three sets of TP220 test probes with three sets of "extended tooth" alligator clips, two sets AC280 hook clips, BP7240 Li-ion battery pack, BC7240 battery charger, C799 field soft case, USB communication cable, getting started guide, instruction manual on CDROM, NIST traceable certificate of calibration, DPC/TRACK 2 sample software that enables upload and printing of calibration records. Model Fluke-754 includes HART communication cable. Includes C799 Field Soft Case. Includes three year warranty. FLUKE-750SW DPC/TRACK 2 Software Included with DPC/TRACK software: Software media, Instruction Manual, USB Cable. FLUKE-700 Pxx Pressure Modules Included with each Fluke Pressure Module: BP-ISO Adapter(s) (except with P29 - P31), Instruction Sheet, NIST traceable calibration report and data, one-year warranty. Accessories Fluke-700PMP Fluke-700LTP-1 Fluke-700PTP-1 Fluke-700HTP-1 Fluke-700HTH-1 Fluke-700PRV-1 Fluke-700-IV Fluke-700PCK Fluke-700BCW Fluke-700TC1 Fluke-700TC2 Fluke-700TLK 754HCC BC7240 BP7240 C700 C781 C799 Pressure Pump; 100 psi/7 bar Low Pressure Test Pump Pneumatic Test Pump; 400 psi/40 bar Hydraulic Test Pump; 10,000 psi/700 bar Hydraulic Test Hose Pressure Relief Valve Kit for HTP Current Shunt (for mA/mA applications) Pressure Calibration Kit Bar Code Wand TC Mini-Plug Kit, 9 types TC Mini-Plug Kit, JKTERS Process Test lead kit Smart instrument communication cable Battery Charger Li-on Battery Pack Hard Carrying Case Soft Carrying Case Soft Field Case 11 Fluke Corporation