Frigidaire FAFS4272LW Complete Owner's Guide (English) - Page 32

Problem, Possible Causes, Solutions, Preventive Measures

Page 32 highlights

SOLUTIONS TO COMMON PROBLEMS Common Washing Problems, continued PROBLEM Residue stains / buildup, mold or mildew stains in gasket Residue stains / buildup, mold or mildew stains in dispenser drawer Water in fold of flexible gasket Odor POSSIBLE CAUSES • Moisture in the washer. • Use of non-HE detergent. • Overdosing detergent. • Overloading wash drum. • Leaving a wet load set in washer. • Cold water washes which may not completely dissolve and remove detergents. • Moisture in the washer. • Use of non-HE detergent. • Overdosing detergent. • Result of washing and part of normal operation. • Moisture in the washer. • Use of non-HE detergent. • Overdosing detergent. • Leaving a wet load remain in washer. • Cold water washes which may not completely dissolve and remove detergents. SOLUTIONS • Perform SYSTEM CLEAN cycle • Scrub gasket with Comet™ Spray Gel Mildew Stain Remover using brush to remove stains. • Use only HE (high efficiency detergent) along with recommended dosage. • Remove wash load immediately upon cycle completion. • Remove dispenser drawer and wipe dispenser and inserts with combination of ¾ cup liquid chlorine bleach and one gallon hot water. Rinse well, and repeat if necessary. Return drawer to location. NOTE: Wear rubber of latex gloves. Protect floor and clothing from bleach damage. • Use only HE (high efficiency detergent) along with recommended dosage. • At the end of each wash, dry inside of gasket fold with clean dry towel all around gasket. • Perform SYSTEM CLEAN cycle. • At the end of each wash, dry inside of gasket fold with clean, dry towel all around gasket. • Use only HE (high efficiency detergent) along with recommended dosage. • Remove wash load immediately upon cycle completion. • Pour one cup liquid chlorine bleach in standpipe; let remain a day and flush with water. PREVENTIVE MEASURES • Run dehumidifier in laundry room. • Avoid overfilling detergent and fabric softener compartments of dispenser. • Dry the inside of washer and gasket after every run. • Avoid overfilling detergent and fabric softener compartments of dispenser. • Leave door and dispenser drawer open for a few hours after use or whenever washer is not in use. 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36

32
SOLUTIONS TO COMMON PROBLEMS
PROBLEM
POSSIBLE CAUSES
SOLUTIONS
PREVENTIVE MEASURES
Residue stains /
buildup, mold or
mildew stains in
gasket
Moisture in the washer.
Use of non-HE detergent.
Overdosing detergent.
Overloading wash drum.
Leaving a wet load set in
washer.
Cold water washes which
may not completely dissolve
and remove detergents.
Perform SYSTEM CLEAN
cycle
Scrub gasket with Comet™
Spray Gel Mildew Stain
Remover using brush to
remove stains.
Use only HE (high ef
ciency
detergent) along with rec-
ommended dosage.
Remove wash load immedi-
ately upon cycle completion.
Run dehumidi
er in laundry
room.
Avoid over
lling detergent
and fabric softener compart-
ments of dispenser.
Dry the inside of washer
and gasket after every run.
Residue stains
/ buildup, mold
or mildew stains
in dispenser
drawer
Moisture in the washer.
Use of non-HE detergent.
Overdosing detergent.
Remove dispenser drawer
and wipe dispenser and
inserts with combination of
¾ cup liquid chlorine bleach
and one gallon hot water.
Rinse well, and repeat if
necessary. Return drawer to
location. NOTE: Wear rub-
ber of latex gloves. Protect
oor and clothing from
bleach damage.
Use only HE (high ef
ciency
detergent) along with rec-
ommended dosage.
Avoid over
lling detergent
and fabric softener compart-
ments of dispenser.
Water in fold of
exible gasket
Result of washing and part
of normal operation.
At the end of each wash,
dry inside of gasket fold
with clean dry towel all
around gasket.
Odor
Moisture in the washer.
Use of non-HE detergent.
Overdosing detergent.
Leaving a wet load remain
in washer.
Cold water washes which
may not completely dissolve
and remove detergents.
Perform SYSTEM CLEAN
cycle.
At the end of each wash,
dry inside of gasket fold
with clean, dry towel all
around gasket.
Use only HE (high ef
ciency
detergent) along with rec-
ommended dosage.
Remove wash load immedi-
ately upon cycle completion.
Pour one cup liquid chlorine
bleach in standpipe; let
remain a day and
ush with
water.
Leave door and dispenser
drawer open for a few
hours after use or whenever
washer is not in use.
Common Washing Problems, continued