Frigidaire FAH106S1T Use and Care Manual - Page 8

Do This, You Will See, Sleep Feature, Check Filter Feature, Remote Sensing Feature On Some Models - air conditioner model

Get Frigidaire FAH106S1T - 10000 BTU Through-the-Wall Air Conditioner PDF manuals and user guides
UPC - 012505273063
View all Frigidaire FAH106S1T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Air Conditioner Features(continued) SLEEP FEATURE: DO THIS: PRESS SLEEP PAD LIGHT ON YOU WILL SEE: The Sleep Mode can be selected with a Heating or Cooling Mode. Note: In this "MODE" the selected cooling temperature will increase by 2 degrees F, 30 minutes after the mode is selected. The temperature will then increase by another 2 degrees F, after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the originally selected temperature. If this Mode is selected with Heat, the set temperature will Decrease at the same time pattern. This ends the "Sleep" MODE and the unit will continue to operate as originally programmed. The "Sleep" MODE program can be cancelled at any time during operation by pressing "Sleep" MODE button. CHECK FILTER FEATURE: LIGHT ON YOU WILL SEE: DO THIS: PRESS TO RESET Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the "Clean Filter" button and the light will go off. REMOTE SENSING FEATURE (on some models) YOU WILL SEE: LIGHT Pulsing On & Off Intermittently DO THIS: PRESS SENSING START BUTTON Note: unit display show "set" temperature Note: This feature can be activated from the remote control ONLY. Note: remote display is actual temperature at remote control only To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing start button. The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each time it sends a signal. It will continue to send this signal until the feature is deactivated by pressing the remote sensing stop button. If the unit does not receive the remote sensing signal during any 3 minute interval, the unit will keep to indicate the remote sensing mode has ended. The display on the remote control indicates the temperature at the remote ONLY. The unit display indicates the set temperature. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
DO THIS:
PRESS
SLEEP PAD
LIGHT ON
YOU WILL SEE:
8
Air Conditioner Features
(continued)
SLEEP FEATURE:
DO THIS:
PRESS TO RESET
LIGHT ON
YOU WILL SEE:
The Sleep Mode can be selected with a Heating or Cooling Mode. Note: In this “MODE” the selected cooling temperature
will increase by 2 degrees F, 30 minutes after the mode is selected. The temperature will then increase by another 2
degrees F, after an additional 30 minutes. This new temperature will be maintained for 7 hours before it returns to the
originally selected temperature. If this Mode is selected with Heat, the set temperature will Decrease at the same time
pattern. This ends the “Sleep” MODE and the unit will continue to operate as originally programmed. The “Sleep” MODE
program can be cancelled at any time during operation by pressing “Sleep” MODE button.
CHECK FILTER FEATURE:
Note: This feature is a reminder to clean the Air Filter (See Care and Cleaning) for more efficient operation and cooling. The
LED (light) will illuminate after 250 hours of operation. To reset after cleaning the filter, press the “Clean Filter” button and
the light will go off.
REMOTE SENSING FEATURE (on some models)
LIGHT Pulsing On
& Off Intermittently
DO THIS:
PRESS SENSING
START BUTTON
Note: unit display show
“set” temperature
Note: remote display is
actual temperature at
remote control only
YOU WILL SEE:
Note: This feature can be activated from the remote control
.
To activate the remote sensing feature, point the remote control towards the unit and press the remote sensing start button.
The LIGHT on the unit control will pulse to indicate it received the signal. The LIGHT on the remote control will pulse each
time it sends a signal. It will continue to send this signal until the feature is deactivated by pressing the remote sensing stop
button. If the unit does not receive the remote sensing signal during any 3 minute interval, the unit will keep to indicate the
remote sensing mode has ended. The display on the remote control indicates the temperature at the remote
. The unit
display indicates the set temperature.
ONLY
ONLY