Frigidaire FAQE7011KW Complete Owner's Guide (English) - Page 7

IMPORTANT, Operating Your Dryer, continued

Page 7 highlights

OPERATING INSTRUCTIONS Operating Your Dryer, continued 2 Check that the lint filter is clean and in place. • A suitable drying temperature, dryness level and options will automatically be indicated for the cycle selected. See the "Dryer Settings Chart" for more details. • To change the drying temperature and dryness level, press the Temperature or Dryness buttons to scroll to the desired settings. • To select or delete an option, press Options; then, while the indicator is blinking, press Select. The indicator will light when the option has been selected. It will no longer be lighted when the option has been deleted. 3 Load the dryer and close the door. • Load items loosely. The average wet load will fill the drum 1/3 to 1/2 full. Items need room to tumble freely for even drying and less wrinkling. • If desired, place a dryer fabric softener sheet on top of the load at the beginning of the cycle. • To save energy and time and avoid uneven drying and wrinkling, do not overload the dryer. • When drying large items, dry only two or three items at a time. Fill out the load with small and medium sized items. • For delicate or very small loads, add two or three similar items to improve tumbling action. 4 Select the appropriate cycle and settings for each load. NOTE Over-drying can cause wrinkles, shrinkage, lint, harshness and a build up of static electricity. • Turn the cycle selector knob in either direction to select the cycle desired. The indicator for that cycle will be illuminated. • The estimated drying time for Auto Dry cycles or the actual drying time for Timed Dry cycles will be displayed. NOTE If a setting is not available for the cycle selected, the indicator will not light. • Adjustments made to a cycle will be remembered and recalled each time that cycle is selected in the future. • To return to factory settings, press the Start/Pause and Select buttons at the same time and hold until the signal sounds. Press and hold both for ten seconds to return to factory settings. 5 Start the cycle. • To add or remove items when the dryer is running, open the door. The dryer will stop when the door is opened. Allow the drum to come to a complete stop before reaching inside. • Close the door and press Start to resume the cycle. 6 When the cycle ends, remove items immedi- ately and hang or fold. IMPORTANT Clean the lint filter after every load. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18

7
OPERATING INSTRUCTIONS
IMPORTANT
Clean the lint filter after every load.
2
Check that the lint filter is clean and in place.
±
NOTE
Over-drying can cause wrinkles, shrinkage, lint,
harshness and a build up of static electricity.
±
NOTE
If a setting is not available for the cycle selected, the
indicator will not light.
3
Load the dryer and close the door.
Load items loosely. The average wet load will
fill the drum 1/3 to 1/2 full. Items need room to
tumble freely for even drying and less wrinkling.
If desired, place a dryer fabric softener sheet on
top of the load at the beginning of the cycle.
To save energy and time and avoid uneven drying
and wrinkling, do not overload the dryer.
When drying large items, dry only two or three
items at a time. Fill out the load with small and
medium sized items.
For delicate or very small loads, add two or three
similar items to improve tumbling action.
4
Select the appropriate cycle and settings for
each load.
A suitable drying temperature, dryness level and
options will automatically be indicated for the cycle
selected. See the “Dryer Settings Chart” for more
details.
To change the drying temperature and dryness
level, press the Temperature or Dryness buttons to
scroll to the desired settings.
To select or delete an option, press Options; then,
while the indicator is blinking, press Select. The
indicator will light when the option has been se-
lected. It will no longer be lighted when the option
has been deleted.
Adjustments made to a cycle will be remembered
and recalled each time that cycle is selected in the
future.
To return to factory settings, press the Start/Pause
and Select buttons at the same time and hold until
the signal sounds.
Turn the cycle selector knob in either direction to
select the cycle desired. The indicator for that cycle
will be illuminated.
The estimated drying time for Auto Dry cycles or
the actual drying time for Timed Dry cycles will be
displayed.
Operating Your Dryer, continued
5
Start the cycle.
To add or remove items when the dryer is running,
open the door. The dryer will stop when the door
is opened. Allow the drum to come to a complete
stop before reaching inside.
Close the door and press Start to resume the cycle.
6
When the cycle ends, remove items immedi-
ately and hang or fold.
Press and hold both for ten seconds
to return to factory settings.