Frigidaire FAQE7011KW Installation Instructions (All Languages)
Frigidaire FAQE7011KW - 7 cu. Ft. Cycle Electric Dryer Drum Manual
UPC - 012505379925
View all Frigidaire FAQE7011KW manuals
Add to My Manuals
Save this manual to your list of manuals |
Frigidaire FAQE7011KW manual content summary:
- Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 1
All about the Installation of your Dryer TABLE OF CONTENTS Important Safety Instructions 2-3 Reversing Door 18-21 Installation Requirements 4-10 Accessories 22 Installed Dryer Dimensions 11 Notes 23-24 Installation Instructions 12-17 Español 25 www.frigidaire.com USA 1-800-944-9044 www. - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 2
risk of fire. • The instructions in this manual and all other literature included with this dryer are not meant to cover every possible condition and situation that may occur. Good safe practice and caution MUST be applied when installing, operating and maintaining any appliance. WHAT TO DO IF YOU - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 3
240v Electric Supply (Electric Dryer) Approved NEMA 10-30R or 14-30R service cord with all screws tight on terminal block Approved strain relief installed Terminal access cover installed before initial operation Door Reversal Follow detailed instructions in this guide Test hinge and latch - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 4
fused circuits for washer and dryer. DO NOT operate a washer and a dryer on the same dryer is in the installed position. GROUNDING CONNECTION - See "Grounding requirements" in Electrical Installation for use with clothes dryers. For 3-wire cord connection instructions see ELECTRICAL CONNECTIONS FOR - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 5
dryer is equipped with a 120 volt 3-wire power cord. GROUNDING CONNECTION - See "Grounding requirements" in Electrical Installation . 1 Installation MUST conform to connect your dryer to the gas supply installed immediately upstream of the gas supply connection to the dryer. 6 The dryer The dryer MUST - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 6
obstruction. WARNING FIRE HAZARD Failure to follow these instructions can create excessive drying times and fire hazards. The following are specific requirements for proper and safe operation of your dryer. WARNING FIRE HAZARD Do not install a clothes dryer with flexible plastic or metal foil venting - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 7
INSTALLATION REQUIREMENTS Exhaust system requirements, continued WARNING FIRE HAZARD A clothes dryer must be exhausted outdoors. Do not exhaust dryer into a chimney, a wall, a ceiling, an attic, a crawl space or any concealed space of a building. A clothes dryer produces combustible lint. If the - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 8
installing a quick-turn 90° dryer vent elbow directly to exhaust outlet of dryer. Dryer vent elbows are available through your local parts distributor or hardware store. CORRECT INCORRECT In installations inches of water column, the system is too restrictive and the installation is unacceptable. - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 9
Part 280) or Standard CAN/CSAZ240 MH. 2 Dryer MUST be exhausted outside (outdoors, not beneath the mobile home) using metal ducting that will not support explosion, fire or burns. IMPORTANT DO NOT INSTALL YOUR DRYER: 1 In an area exposed to dripping water or outside weather conditions. 2 In an area - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 10
or closet, MUST be exhausted outdoors. 2 No other fuel burning appliance shall be installed in the same closet as the gas dryer. 3 Your dryer needs the space around it for proper ventilation. DO NOT install your dryer in a closet with a solid door. 4 Closet door ventilation required: A minimum - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 11
open door 29.75" (75.5cm)* to front of closed door INSTALLED DIMENSIONS 27.0" (68.5cm) 36.0" (91.5cm) 51.25" (130cm) freestand dryer on floor floor line gas supply pipe on rear of gas unit 1.6" (4cm) dryer mounted on optional pedestal floor line * To obtain these minimal depth dimensions - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 12
installation of your dryer. Failure to follow these instructions can create electrical shock and/or a fire hazard. WARNING ELECTRICAL SHOCK HAZARD • This appliance MUST be properly grounded. Electrical shock can result if the dryer is not properly grounded. Follow the instructions in this manual - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 13
INSTALLATION INSTRUCTIONS Grounding requirements - Electric dryer (Canada) WARNING ELECTRICAL SHOCK HAZARD Improper connection of the equipment grounding conductor can result in a risk of electrical shock. Check with a licensed electrician if you are in doubt as to whether the appliance is - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 14
INSTALLATION INSTRUCTIONS Gas connection 1 Remove the shipping cap from gas pipe at the rear of the dryer. IMPORTANT DO NOT connect the dryer to L.P. gas service without converting the gas valve. An L.P. conversion kit must be installed by a qualified gas technician. 2 Connect a 1/2 inch (1.27 cm) - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 15
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 16
the screw securing the terminal block access cover in the lower corner on the back of the dryer. 3 Install a UL-approved strain relief according to the power cord/strain relief manufacturer's instructions in the power cord entry hole below the access panel. At this time, the strain relief should - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 17
time and money. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 18
then upper screw. 4 Gently place dryer door face down on flat, covered work surface. 5 Locate the 5 indented head screws (no. 1-5) in the small, circular recesses (at 11, 1, 4, 6, and 8 o'clock positions) of the inner door. Remove and save these 5 screws. 3 Supporting door with both hands, squarely - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 19
Reversing the hinge 1 Carefully pull out the 2 small round hole plugs from the front panel and save. Remove and save the square "T" slot cover by sliding it up and pulling it out. Move all 3 plugs to the opposite side of the front panel and insert. ROUND PLUG REVERSING DOOR 4 From the back side of - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 20
hole in the outer door. 3 Replace indented head screws (no. 1-5) removed earlier. Take care not to strip out the plastic holes. 4 Replace pan head screws (no. 6-7) 5 Locate new metal strike supplied with dryer manuals. Grip new strike with pliers as shown below. Firmly insert the strike so it - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 21
FRONT PANEL REVERSING DOOR 3 Close the door and test operation of hinge, strike and latch. 2 While supporting the door, install the upper pan head screw first and then the lower one. Í NOTE Correctly installed hinge screws will press hinge flush to front panel. Any gap between hinge and front panel - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 22
Canada 1-800-265-8352) If replacements parts are needed for your dryer, contact the source where you purchased your dryer, call 1-800944-9044 (in Canada 1-800-265-8352), or visit our website, www.frigidaire.com, for the Frigidaire Authorized Parts Distributor nearest you. WARNING ELECTRICAL SHOCK - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 23
NOTES 23 - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 24
NOTES 24 - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 25
la puerta 42-45 Requisitos de instalación 28-34 Accesorios 46 Dimensiones de la secadora instalada 35 Notas 47 Instrucciones de instalación 36-41 www.frigidaire.com UEES.AU1U-8.10-08-0904-49-4940-494044 wwwww.fwrig.firdigaidrea.icrea.caCanCaadnaad1á-810-08-0206-52-6853-582352 - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 26
un instalador calificado, agencia de servicios o proveedor de gas. • Instale la secadora de ropa de acuerdo con las instrucciones del fabricante y los á, el CSA C22.1 del Código Eléctrico de Canadá (Canadian Electrical Code) Parte 1. • El servicio de gas de la secadora debe cumplir con los códigos y - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 27
instrucciones antes de usar este secadora. Identificación de los símbolos, palabras y avisos de seguridad Las indicaciones de seguridad incluidas en este manual aparecen precedidas de un aviso titulado "ADVERTENCIA" o "PRECAUCIÓN", de acuerdo con el nivel de riesgo. Definiciones Este es el símbolo de - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 28
REQUISITOS DE INSTALACIÓN Í NOTA Debido a posibles variaciones en el voltaje, no se recomienda utilizar esta secadora con electricidad generada a partir de generadores a gas, solares, eólicos ni de ninguna otra clase que no sean los empleados por su empresa de electricidad local. Requisitos elé - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 29
REQUISITOS DE INSTALACIÓN Requisitos eléctricos de la secadora a gas: CIRCUITO - Circuito individual de bifurcación de 15 amp., correctamente polarizado y con conexión a tierra con fusible de retardo de 15 amp. o con interruptor automático. SUMINISTRO ELÉCTRICO: corriente alterna de 2 cables, con - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 30
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape Utilice solo un conducto de metal flexible o rígido de 10,2 cm (4 pulgadas) de diámetro (mínimo) y una capucha de ventilación aprobada que tenga uno o más reguladores de tiro que se abran cuando la secadora esté en funcionamiento. Cuando la - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 31
de incendio. • No bloquee los extremos de escape del sistema de ventilación, ni utilice tornillos, remaches ni otros sujetadores que se extiendan hacia la parte interna del conducto para ensamblarlo. Es posible que la pelusa quede atrapada en el filtro, los tornillos o los remaches, lo que puede - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 32
REQUISITOS DE INSTALACIÓN Requisitos del sistema de escape (continuación) Instale los accesorios macho en la dirección correcta: Dirección del escape El escape direccional se puede lograr mediante la instalación de un codo de ventilación de - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 33
Norma de Seguridad y Construcción de Casas Rodantes, título 24 CFR, Parte 32-80 (que anteriormente se conocía como la Norma Federal de Seguridad sistema de escape, consulte las secciones anteriores de esta guía. 5 Cuando se instale una secadora a gas en una casa rodante, se debe dejar espacio en el - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 34
espacio a su alrededor para que la ventilación sea adecuada. NO instale la secadora en un armario con puerta maciza. 4 Ventilación requerida 1cm²) Í NOTA Para lograr una instalación con 0 cm (0") de despeje en la parte trasera de la secadora (para otra que no sea la ventilación hacia atrás), se debe - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 35
del piso 51.25" (130cm) tubería de suministro de gas en la parte trasera de la unidad de gas 1.6" (4cm) 16.9" (43cm) * Para )* al frente de la puerta cerrada 27.0" (68.5cm) suministro eléctrico en la parte trasera de la unidad altura de la línea central para ventilación trasera 3.7" (9.5cm) 19 - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 36
INSTRUCCIONES DE INSTALACIÓN Instalación eléctrica Los siguientes son requisitos necesarios para la instalación eléctrica segura y correcta de su secadora. El no seguir estas instrucciones puede producir una descarga eléctrica y/o incendio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA • Este - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 37
INSTRUCCIONES DE INSTALACIÓN Requisitos de conexión a tierra: secadora eléctrica (Canadá) ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA Una conexión incorrecta del conductor de conexión a tierra del equipo puede provocar un peligro de descarga eléctrica. Si no está seguro de haber realizado - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 38
gases licuados en todas las conexiones de los tubos. FLUJO DE GAS Válvula de cierre manual Conector doble Conector doble Cerrado Conector Abierto Conector flexible Tubo de admisión en la parte posterior de la secadora Todas las conexiones deben estar ajustadas con llave IMPORTANTE La línea - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 39
que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por ) Línea 1 (terminal de LATÓN) Connexión tierra interna (tornillo VERDE) Instale aquí un dispositivo de liberación de tensión aprobado por U.L. Ranura de - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 40
que se encuentra en la esquina inferior de la parte trasera de la secadora. 3 Instale un dispositivo de liberación de tensión aprobado por PLATEADA) Línea 1 (terminal de LATÓN) Connexión tierra interna (tornillo VERDE) Instale aquí un dispositivo de liberación de tensión aprobado por U.L. Ranura de - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 41
cuidadosamente. Ajuste una o varias de las patas de la secadora hasta que se encuentre firme sobre las cuatro patas. Coloque un nivel en la parte superior A de la secadora. La secadora DEBE estar nivelada y firme sobre las cuatro patas. Presione las distintas esquinas para asegurarse de que la - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 42
INVERSIÓN DE LA PUERTA Cómo extraer la puerta 1 Proteja las superficies de trabajo planas, como la parte superior de la secadora o el piso cerca de ésta utilizando un paño o toalla suave. 2 Abra la puerta de la secadora y retire los dos tornillos de - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 43
de ella para retirarla. Mueva los 3 tapones al lado opuesto del panel delantero. TAPÓN REDONDO TAPÓN CUADRADO INVERSIÓN DE LA PUERTA 4 Desde la parte trasera de la puerta interior, presione las lengüetas de retención del tapón de plástico cuadrado para liberarlo. Guarde el tapón cuadrado para - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 44
del recorte de la bisagra. Gire la puerta interior hacia abajo sobre la puerta exterior. 5 Ubique el nuevo pestillo de metal proporcionado con los manuales de la secadora. Sostenga el pestillo nuevo con alicates como se muestra abajo. Inserte firmemente el pestillo de manera que quede en posici - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 45
manos, introduzca la pieza en forma de "T" que se encuentra en la parte trasera de la bisagra en la ranura en forma de "T" del panel delantero el pestillo y el gancho funcionan correctamente. 2 Mientras apoya la puerta, instale el tornillo de cabeza alomada superior primero y luego el inferior. Í - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 46
ó, llame al 1-800-944-9044 (en Canada 1-800-265-8352) o visite nuestro sitio web en www.frigidaire.com para ponerse en contacto con la distribuidora autorizada de repuestos Frigidaire más cercana a su domicilio. ADVERTENCIA PELIGRO DE DESCARGA ELÉCTRICA Cuando se reparen los controles, rotule todos - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 47
NOTAS 47 - Frigidaire FAQE7011KW | Installation Instructions (All Languages) - Page 48
www.frigidaire.com
USA 1-800-944-9044
www.frigidaire.ca
Canada 1-800-265-8352
All about the
Installation
of your
Dryer
Important Safety Instructions
..............................
2-3
Installation Requirements
.................................
4-10
Installed Dryer Dimensions
..................................
11
Installation Instructions
..................................
12-17
Reversing Door
..............................................
18-21
Accessories
.........................................................
22
Notes
............................................................
23-24
EspaƱol
..............................................................
25
TABLE OF CONTENTS
137112200B (0903)