Frigidaire FAQG7021LW Product Specifications Sheet (English) - Page 3
Front Load Dryer Specifications, Optional Accessories
![]() |
UPC - 012505383427
View all Frigidaire FAQG7021LW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
Frigidaire Affinity (All L Models excluding FAQG7021L) Front Load Dryers FAQG7021L B / W 7.0 Cu. Ft. Gas Front Load Dryer Specifications • Product Shipping Weight (approx.) - 140 Lbs. • An electrical supply with grounded three-prong receptacle is required. The power supply circuit must be installed in accordance with current edition of National Electrical Code (ANSI/NFPA 70) and local codes & ordinances. (Do not use same circuit as washer.) • Voltage Rating - 120V / 60 Hz / 15 Amps • Amps @ 120 Volts = 7 Amps • Connected Load (kW Rating) @ 120 Volts = 0.5 kW • Equipped with 120V 3-wire power supply cord, approx. 60" long. • Always consult local and national electric & gas codes. • Can be installed alone, with or without optional 15" Drawer Pedestal, or stacked above matching Frigidaire® Affinity Washer, which requires installation of optional Dryer Stacking Kit. (For installation details, refer to instructions included with optional pedestal or stacking kit or on web.) • Can be built in with matching Frigidaire® Affinity Washer in undercounter, recessed or closet installation. (Refer to Built-In Installations on this page for cutout dimensions. For additional installation details, refer to Product Installation Guide on web.) • Closet installation requires vented door with 2 unobstructed louvered openings, minimum 60 sq. in. each, located 3" from top and bottom of door. Full-length 120 sq. in. opening also acceptable. Allow additional 1" clearance between fronts of units and closed door. • Do NOT install in area exposed to dripping water or outdoor weather conditions; where gasoline or other flammables are kept or stored; or where dryer comes in contact with curtains, drapes or anything that will obstruct flow of combustion and ventilation air. • For garage installation, dryer MUST be located minimum 18" above floor. • Floor MUST be solid with 1" maximum slope. Do NOT install on carpeted surface. • Dryer MUST exhaust to outside of building, NOT into any concealed space. • Exhaust installation requires minimum 4"-diameter rigid or flexible metal duct with approved vent hood having swing-out damper(s). Do NOT use flexible plastic or metal foil duct and use shortest run possible. • Gas supply line should be 1/2" pipe and MUST have individual shutoff valve. • Leveling legs supplied to level dryer properly and reduce excessive noise and vibration. Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions. Optional Accessories • Dryer Stacking Kit - (PN # STACKIT4X). • 15" Classic Black Drawer Pedestal - (PN # CFPWD15B). • 15" Classic White Drawer Pedestal - (PN # CFPWD15W). • Mobile Home Installation Kit - (PN # 137067200). • LP Gas Conversion Kit - (PN # PCK4200). • Drying Rack - (PN # 137067300). USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FAQG7021L 10/10 © 2010 Electrolux Home Products, Inc. Specifications subject to change. Printed in the U.S.A.
![](/manual_guide/products/frigidaire-faqg7021lb-product-specifications-sheet-english-a091715/3.png)