Frigidaire FAS226R2A Use and Care Manual - Page 9

Remote Sensing Feature, To Turn Unit Off, You Will See

Page 9 highlights

Air Conditioner Features (continued) REMOTE SENSING FEATURE (on some models) : LIGHT pulsing On Off intermittently. T emp/Timer T emp/Timer Fa n S l o w e r Fa n S l o w e r F an F aster F an F aster T emp/Timer Cool Ener g y Fa n Sa ver Onl y Slee p Au t o T emp Timer Staorpt R emote Sensing DO THIS: PRESS REMOTE SENSING BUTTON ON T emp/Timer Cool Ener g y Fa n Sa ver Onl y Slee p Au t o T emp Timer Staorpt R emote Sensing NOTE:Unit display shows"set"temperature NOTE: Remote display is actual temperature at remote control only Note: This feature can be activated from the remote control ONLY,the unit must be in a cooling mode. To activate the remote sensing feature,point the remote control towards the unit and press the remote sensing button.Next,use the buttons to set the desired temperature at the remote.(Note that the set temperature will only be displayed on the unit itself).The LIGHT on the unit control will pulse to indicate it received the signal.The LIGHT on the remote control will pulse each time it sends a signal.It will continue to send this signal until the feature is deactivated by pressing the remote sensing button.If the unit does not receive the remote sensing signal during any 3 minute interval,the unit will beep to indicate the remote sensing mode has ended.The display on the remote control indicates the temperature at the remote ONLY. The unit display indicates the set temperature. Remote Sensing:The Remote Sensing function is terminated using the remote control Start/Stop button or the Remote Sensing Stop button, and also the main Start/Stop button on the unit. HEATING FEATURE (on some modes) YOU WILL SEE: DO THIS: PRESS MODE BUTTON SELECT HEAT Note: This feature can be used with any combination of FAN Speeds, Timer, or Sleep Modes.When in the "Heat" Mode,the fan will run continuously while heat is needed. The temperature will automatically be maintained anywhere between 55 F(13) and 80 F(27) When the room set temperature is satisfied,the fan will cycle off and on to circulate and sample the room air. TO TURN UNIT OFF: YOU WILL SEE: DO THIS: PRESS ON/OFF BUTTON Note: When unit is shut off in the Heat Mode, the fan will continue to run for a few seconds to dissipate residual heat within the unit. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12

9
T emp/Timer
F an
F aster
Fa n S l o w e r
T emp/Timer
Cool
Ener
gy
Sa ver
Fa n
Onl y
Slee
p
Au t o
T emp
Timer
Start
R emote
Sensing
T emp/Timer
F an
F aster
Fa n S l o w e r
T emp/Timer
Cool
Ener
gy
Sa ver
Fa n
Onl y
Slee
p
Au t o
T emp
Timer
Start
R emote
Sensing
Stop
Stop
Remote Sensing:The Remote Sensing function is terminated using the remote control Start/Stop
button or the Remote Sensing
Stop button, and also the main Start/Stop button
on the unit.
Air Conditioner Features
(continued)
REMOTE SENSING FEATURE
(on some models) :
LIGHT pulsing On
Off intermittently.
DO THIS:
PRESS REMOTE
SENSING
BUTTON ON
NOTE:
Unit display shows"set"temperature
remote control only
is actual temperature at
NOTE:
Remote display
Note:
This feature can be activated from the remote control ONLY,the unit must be in a cooling mode.
To activate the remote sensing feature,point the remote control towards the unit and press the remote sensing button.Next,use the
buttons to set the desired temperature at the remote.(Note that the set temperature will only be displayed on the unit itself).The LIGHT on
the unit control will pulse to indicate it received the signal.The LIGHT on the remote control will pulse each time it sends a signal.It will con-
tinue to send this signal until the feature is deactivated by pressing the remote sensing button.If the unit does not receive the remote sensing
signal during any 3 minute interval,the unit will beep to indicate the remote sensing mode has ended.The display on the remote control indicates
the temperature at the remote ONLY. The unit display indicates the set temperature.
HEATING FEATURE
(on some modes)
PRESS
DO THIS:
MODE BUTTON
SELECT HEAT
Note:
This feature can be used with any combination of FAN Speeds, Timer, or Sleep Modes.When in the "Heat" Mode,the fan will run
continuously while heat is needed. The temperature will automatically be maintained anywhere between 55
F(13
) and 80
F(27
)
When the room set temperature is satisfied,the fan will cycle off and on to circulate and sample the room air.
Note:
When unit is shut off in the Heat Mode, the fan will continue to run for a few seconds to dissipate
residual heat within the unit.
TO TURN UNIT OFF:
YOU WILL SEE:
DO THIS:
PRESS
ON/OFF BUTTON
YOU WILL SEE: