Frigidaire FASE7021NW Product Specifications Sheet (English) - Page 3
Front Load Dryer Specifications, Optional Accessories - affinity
View all Frigidaire FASE7021NW manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
Frigidaire Affinity (All N Models) Front Load Dryer FASE7021N W 7.0 Cu. Ft. Electric Front Load Dryer Specifications • Product Shipping Weight (approx.) - 140 Lbs. • An electrical supply with grounded three-prong receptacle is required. • Voltage Rating - 240V / 60 Hz / 30 Amps • Single phase 3- or 4-wire cable, 240 Volt, 60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line. (Do not use same circuit as washer.) • Connected Load (kW Rating) @ 240 Volts = 5.4 kW • Amps @ 240 Volts = 24 Amps • Dryer MUST employ a 3-conductor NEMA 10-30 type SRDT or 4-conductor NEMA 14-30 type SRDT or ST (as required), rated at 240 volt AC minimum, 30 amp power supply cord marked for use with clothes dryers (not supplied). • Grounding through neutral link prohibited in specific applications and certain locales, requiring use of 4-wire system. (For detailed electrical requirements, refer to Product Installation Guide on web.) • Always consult local and national electric & plumbing codes. • Can be installed alone, with or without optional 15" Drawer Pedestal, or stacked above matching Frigidaire® Affinity Washer, which requires installation of optional Dryer Stacking Kit. (For installation details, refer to instructions included with optional pedestal or stacking kit or on web.) • Can be built in with matching Frigidaire® Affinity Washer in undercounter, recessed or closet installation. (Refer to Built-In Installations on this page for cutout dimensions. For additional installation details, refer to Product Installation Guide on web.) • Closet installation requires vented door with 2 unobstructed louvered openings, minimum 60 sq. in. each, located 3" from top and bottom of door. Full-length 120 sq. in. opening also acceptable. Allow additional 1" clearance between fronts of units and closed door. • Do NOT install in area exposed to dripping water or outdoor weather conditions; where gasoline or other flammables are kept or stored; or where dryer comes in contact with curtains, drapes or anything that will obstruct flow of combustion and ventilation air. • For garage installation, dryer MUST be located minimum 18" above floor. • Floor MUST be solid with 1" maximum slope. Do NOT install on carpeted surface. • Dryer MUST exhaust to outside of building, NOT into any concealed space. • Exhaust installation requires minimum 4"-diameter rigid or semi-rigid metal duct with approved, unobstructed vent hood having swing-out damper(s). If installing rigid metal duct (preferred), do not exceed MAXIMUM venting run length of 64 ft., allow deductions for elbows and vents. If installing semi-rigid metal duct, do not exceed MAXIMUM venting run length of 8 ft., always allow deductions for elbows and vents (Refer to Product Installation Guide on web for additional information). Do NOT use flexible plastic or metal foil duct and use shortest run possible. • Leveling legs supplied to level dryer properly and reduce excessive noise and vibration. • Water inlet hose for steam setting connects to cold water supply with "Y" connector and requires 3/4" clearance between back of unit and wall. Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions. Optional Accessories • Dryer Stacking Kit - (PN # STACKIT4X). • 15" Classic White Drawer Pedestal - (PN # CFPWD15W). • Mobile Home Installation Kit - (PN # 137067200). • Drying Rack - (PN # 137067300). USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FASE7021N 03/12 © 2012 Electrolux Home Products, Inc. Specifications subject to change.