Frigidaire FASG7021NW Installation Instructions (All Languages) - Page 19

Frigidaire FASG7021NW Manual

Get Frigidaire FASG7021NW PDF manuals and user guides View all Frigidaire FASG7021NW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

INSTALLATION INSTRUCTIONS General installation 1 Connect the exhaust duct to the outside exhaust system (see pages 6 through 8). Use of a 4" (102 mm) clamp (item A) is recommended to connect the dryer to the exhaust vent system. Use metal foil tape to seal all other joints. 2 Carefully slide the dryer to its final position. Adjust one or more of the legs until the dryer is resting solidly on all four legs. Place a level on top of the dryer. The dryer MUST be level and resting solidly on all four legs. Rock alternating corners to check for stability. Remove and discard door tape. A IMPORTANT Be sure the power is off at a circuit breaker/fuse box before plugging the power cord into an outlet. 3 Plug the power cord into a grounded outlet. 4 Turn on the power at the circuit breaker/fuse box. 5 Read the Use & Care Guide provided with the dryer. It contains valuable and helpful information that will save you time and money. 6 If you have any questions during initial operation, please review the "Avoid Service Checklist" in your Use & Care Guide before calling for service. 7 Place these instructions in a location near the dryer for future reference. Í NOTE A wiring diagram and technical data sheet are located inside the dryer console. Grounding type wall wa ll receptacl receptacle Do not, under any an y circumstances, circumstances, cut, remo remove ve, or bypass bypass the th grounding gr ounding prong. prong. Power cord with Power 3-prong gr grounded ounded plug 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
19
INSTALLATION INSTRUCTIONS
General installation
Grounding type
Grounding type
wa
wall receptacl
ll receptacle
Po
Power cord with
wer cord with
3-prong
3-prong gr
grounded plug
ounded plug
Do not,
Do not, under
under
an
any cir
y circumstances,
cumstances,
cut,
cut, remo
remove
ve,
or b
or bypass th
ypass the
gr
grounding pr
ounding prong.
ong.
Í
NOTE
A wiring diagram and technical data sheet are located
inside the dryer console.
1
Connect the exhaust duct to the outside exhaust
system (see pages 6 through 8). Use of a 4” (102
mm) clamp (item A) is recommended to connect
the dryer to the exhaust vent system. Use metal
foil tape to seal all other joints.
2
Carefully slide the dryer to its final position.
Adjust
one or more of the legs until the dryer is resting
solidly on all four legs. Place a level on top of the
dryer. The dryer MUST be level and resting solidly
on all four legs. Rock alternating corners to check
for stability. Remove and discard door tape.
3
Plug the power cord into a grounded outlet.
4
Turn on the power at the circuit breaker/fuse box.
5
Read the Use & Care Guide provided with the dryer.
It contains valuable and helpful information that
will save you time and money.
6
If you have any questions during initial operation,
please review the “Avoid Service Checklist” in your
Use & Care Guide before calling for service.
7
Place these instructions in a location near the dryer
for future reference.
A
IMPORTANT
Be sure the power is off at a circuit breaker/fuse box
before plugging the power cord into an outlet.