Frigidaire FFBD2412SM Wiring Diagram - Page 1

Frigidaire FFBD2412SM Manual

Page 1 highlights

W *SOME MODELS for injury or damage of any kind arising from the use of this Service Products North America cannot be responsible, nor assume any liability, considered acceptable in the appliance repair trade. Electrolux Home Artwork: A06401801Rev001 P/N: A06401801RevA This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally SERVICE DATA SHEET COLOR CODE OPERATION BK............Black BU............Blue PK............Pink R Red Viol..........Violet W White Y Yellow R-Y.........Red/Yellow R-BK......Red/Black To start To delay start --------- To select a new cycle or option To cancel a cycle Close door fully to latch. Press START/CANCEL pad. Close door fully to latch. Press DELAY START pad to select desired delay time. Press desired cycle and/or option pad. The indicator lights will change. Press START/CANCEL within 15 seconds to begin cycle. Hold START/CANCEL pad for 3 seconds, the dishwasher will drain for 90 seconds, then shut off. Interval Number Description Interval Duration Sec. Water Valve Circulation Motor Drain Motor Heater Dispenser Vent Washing LED Sanitize LED Drying LED Clean LED Notes WATER/SERVICE TEST The water/service test, (WST) is a special function initiated from the power failure mode. While in power failure mode - simultaneously press the HEAT DRY and START/CANCEL pads for one half second. The dishwasher will then step through the test cycle per the 1 Fill/Det. Dispenser 2 Fill 60 1 0 0 0 1 1 1 0 0 0 27 1 0 0 0 0 1 1 0 0 0 chart. Pushing the START/CANCEL 3 Wash 45 0 1 0 0 0 1 1 0 0 0 pad will advance the dishwasher to the next step. To Exit the WST - Open and Close the door. 4 Pause 0.4 0 0 0 1 0 1 1 0 0 0 5 Wash/Heat 75 0 1 0 1 1 1 1 0 0 0 6 Wash/Heat/Det. Disp. 60 0 1 0 1 0 1 1 0 0 0 7 Drain 90 0 0 1 0 0 1 1 0 1 0 8 Dry 90 0 0 1 x 0 0 0 1 0 0 End State 0 0 000 0 0 10 1 X - denotes selectable option Clean LED stays on until door is opened or cycle is started BU P3-5 VIO P3-4 Y P3-9 Y P3-10 R-Y P3-1 ELECTRONIC CONTROL BOARD P3-2 R-BK FLOAT SWITCH PK P3-3 HI-LIMIT THERMOSTAT R P8 WARNING DISPLAY CODES (LED) Disconnect electrical power at the fuse box or circuit breaker box before servicing under this product. Electrical power may be present on some parts under this product, even if not in use. Failure to follow this warning could result in serious injury or death. WASHING Washing portion of cycle. SANITIZED ----------The SANITIZATION criteria has been met. Indicator light switch off when door is closed. DRYING Drying portion of cycle. CLEAN Shows Completion of cycle. Indicator light will switch off when door is opened. ALL LED's flashing All LED's flashing indicates power failure has occurred. Press START/CANCEL pad and re-select desired options and cycles. START LED flashing The START LED will flash when the door is opened. Close the door and press START/CANCEL to resume cycle. WIRING DIAGRAM DOOR L1 BK SWITCH NEUT W BK BK W P3-6 P1 P3-7 120VAC 60HZ DISPENSER W *VENT SYSTEMS W WATER VALVE W HEATER W W PUMP MOTOR DRAIN MOTOR W THERMISTOR Data Sheet. CYCLE SELECTION OPTIONS Minutes 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 Heavy Wash Pre-Wash 1 Pre-Wash 2 Pre-Wash 3 Main Wash Rinse 1 Rinse 2 Rinse 3 Final Rinse Dry Water Valve Circulation Motor Drain Motor Heater Dispenser Vent Minutes 5 10 15 20 *Rinse Only Pre-Wash 1 Pre-Wash 2 Water Valve Circulation Motor Drain Motor Heater Dispenser Vent Normal (HT) Pre-Wash 1 Pre-Wash 2 Pre-Wash 3 Pre-Wash 4 Main Wash Rinse 1 Final Rinse Dry Water Valve Circulation Motor Drain Motor Heater Dispenser Vent Note: The Main Wash and Final Rinse may be lengthened when needed to reach optimal wash temperatures. * Some Models Normal Water Valve Circulation Motor Drain Motor Heater Dispenser Vent Minutes Pre-Wash 1 Main Wash Rinse 1 Final Rinse Dry 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 K4 03-05-14 (2014 ESTAR) *Energy Saver Pre-Wash 1 Main Wash Rinse 1 Final Rinse Dry Water Valve Circulation Motor Drain Motor Heater Dispenser Vent Minutes 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80

  • 1
  • 2

SERVICE DATA SHEET
P/N: A06401801RevA
Artwork: A06401801Rev001
This information is intended for use by persons having electrical and
mechanical training and a level of knowledge of these subjects generally
considered acceptable in the appliance repair trade.
Electrolux Home
Products North America cannot be responsible, nor assume any liability,
for injury or damage of any kind arising from the use of this Service
Data Sheet.
BK
............
Black
BU
............
Blue
PK
............
Pink
R
..............
Red
Viol
..........
Violet
W
.............
White
Y
..............
Yellow
R-Y
.........
Red/Yellow
R-BK
......
Red/Black
COLOR CODE
OPERATION
WARNING
DISPLAY CODES (LED)
WIRING DIAGRAM
CYCLE SELECTION OPTIONS
To start -----------------
Close door fully to latch.
Press START/CANCEL pad.
To delay start ---------
Close door fully to latch.
Press DELAY START pad to select desired
delay time.
To select a new cycle
or option -------------
Press desired cycle and/or option pad.
The indicator lights will change.
Press START/CANCEL within
15 seconds to begin cycle.
To cancel
a cycle ----------------
Hold START/CANCEL pad for 3 seconds, the dishwasher will drain for
90 seconds, then shut off.
Disconnect electrical power at
the fuse box or circuit breaker
box before servicing under
this product.
Electrical power
may be present on some parts
under this product, even if
not in use.
Failure to follow this warning
could result in serious injury or
death.
Interval Number
Description
1
2
6
4
3
5
7
8
Fill/Det. Dispenser
Fill
Wash
Wash/Heat/Det. Disp.
Wash/Heat
Pause
Drain
Dry
End State
Interval Duration Sec.
60
27
45
0.4
75
60
90
90
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
Vent
Washing LED
Sanitize LED
Drying LED
Clean LED
0
1
0
1
1
1
1
1
0
1
1
1
x
1
0
0
1
0
1
1
0
1
1
0
1
0
0
0
1
0
0
0
0
0
0
1
0
0
0
0
0
1
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
0
0
0
0
0
1
1
1
0
0
0
0
0
0
1
1
0
0
0
0
1
0
0
0
0
0
1
X - denotes selectable option
Clean LED stays on until door is opened or cycle is started
Notes
0
0
0
0
0
0
WATER/SERVICE TEST
The water/service test, (WST)
is a special function initiated
from the power failure mode.
While in power failure mode
- simultaneously press the HEAT
DRY and START/CANCEL pads for
one half second.
The dishwasher will then step
through the test cycle per the
chart.
Pushing the START/CANCEL
pad will advance the dishwasher
to the next step.
To Exit the WST
- Open and
Close the door.
PUMP MOTOR
DRAIN MOTOR
VIO
120VAC
60HZ
ELECTRONIC
CONTROL
BOARD
*SOME MODELS
P3-4
BU
DISPENSER
R-Y
W
P3-1
W
W
R-BK
W
*VENT SYSTEMS
HEATER
W
HI-LIMIT
THERMOSTAT
R
P8
WATER VALVE
FLOAT
SWITCH
PK
P3-3
W
Y
P3-10
P3-9
P3-5
P3-7
DOOR
SWITCH
W
NEUT W
L1
BK
BK
BK
P3-6
P1
W
Y
THERMISTOR
P3-2
Pre-Wash 1
Minutes
Normal
(HT)
Water Valve
Heavy Wash
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
105
110
115
120
125
5
10
15
20
5
10
15
20
25
30
35
40
45
Pre-Wash 2
Pre-Wash 3
Main Wash
Rinse 1
Rinse 2
Rinse 3
Final Rinse
Dry
Circulation Motor
Drain Motor
Heater
Dispenser
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
Pre-Wash 1
Pre-Wash 2
Pre-Wash 3
Main Wash
Rinse 1
Final Rinse
Dry
Pre-Wash 4
Minutes
Water Valve
*Rinse Only
Circulation Motor
Drain Motor
Heater
Dispenser
Pre-Wash 1
Pre-Wash 2
50
55
60
65
70
75
80
85
90
Normal
Minutes
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
Pre-Wash 1
Main Wash
Rinse 1
Dry
*Energy Saver
Minutes
5
10
15
20
25
30
35
40
45
50
55
60
65
70
Pre-Wash 1
Main Wash
Final Rinse
Water Valve
Circulation Motor
Drain Motor
Heater
Dispenser
75
80
Rinse 1
Dry
Vent
Vent
Vent
Final Rinse
Vent
Vent
K4 03-05-14 (2014 ESTAR)
Note: The Main Wash and Final Rinse
may be lengthened when needed to reach
optimal wash temperatures.
130
135
* Some Models
WASHING -----------
Washing portion of cycle.
SANITIZED ----------
The SANITIZATION criteria has been met.
Indicator
light switch off when door is closed.
DRYING -------------
Drying portion of cycle.
CLEAN----------------
Shows Completion of cycle.
Indicator
light will
switch off when door is opened.
ALL LED’s
flashing--------------
All LED’s flashing indicates power failure has occurred.
Press
START/CANCEL pad and re-select desired options and cycles.
START LED
flashing--------------
The START LED will flash when the door is opened.
Close the
door and press START/CANCEL to resume cycle.