Frigidaire FFCD2413US Product Specifications Sheet - Page 3
Front, Right - dimensions
View all Frigidaire FFCD2413US manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
24" Built-In Dishwasher w/Ready-Select Slim Controls (RSFDFISSCHCDW)24Aw1S3H/UPESRl/aWs/tBic Tub (PT) Baseline 24" BUILT-IN Front 24" Left 25" Right 49 1/4" 22 1/2" 33 1/2" Adjustable to 35" Door in 90° open position 16 3/8" 3 3/4" Water inlet valve Power supply location 17 3/4" (right bottom front) To junction box 90° 341/4" min. 24" min. 90° Electrical, water, and drain lines must be confined to shaded area 18" 4" 7 3/4" 3" Hot Electrical water wiring 6" line 6" 2 1/2" 2 1/2" 24" INSTALLATION SPECIFICATIONS • Product Shipping Weight (approx.) - 83 Lbs. • Voltage Rating - 120V / 60 Hz / 15 Amps (maximum 20 Amps if connected with disposer) • Connected Load (kW Rating) @ 120 Volts = 1.44 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120V = 10 Amps • Always consult local and national electric & plumbing codes. Meets requirements of ASSE 1006 - integral air gap on supply. • Water Pressure - Hot water line to dishwasher must provide between 20 and 120 pounds per square inch (psi) with at least 120° F hot water temperature. • Make sure location has correct drain, water and electrical outlets to make connections - MUST be confined to shaded areas. • Electrical and water supplies should enter cabinet opening on floor, or through back or side walls, as shown in shaded areas. • Keep back free of drain, water & electrical supply. • Connections preferably located toward left side of dishwasher. Do not cross drain, water or electrical lines in front of motor, blower or frame. • If connecting drain hose to sink trap, local code may require installation of Air Gap Kit (not included). • Leveling legs supplied to adjust height. (Note: Height only adjustable to 35-3/4" max. when installed in 35-3/4" max. standard cabinetry cutout. 5/16" min. clearance required from top of unit to underside of countertop. Dimensions do NOT include insulation - insulation blanket may be compressed during installation.) • When installing adjacent to wall, cabinet or other obstruction that extends beyond front edge of unit, allow 2" minimum clearance between opened door and obstruction. • Floor should be flat and free of obstructions with carpet removed to provide motor clearance. • When installing at end of cabinet line, sides and back must be fully enclosed. • Do not install unit under a cooktop, damage will occur. • Recommended to seal cabinets, enclosing all sides of dishwasher, including underside of countertop, with oil-based paint or moisture-proof polyurethane to prevent possible steam/moisture damage. Meets requirements of ASSE 1006 Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes. Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com / frigidaire.ca. Specifications subject to change. Accessories information available on the web at frigidaire.com / frigidaire.ca USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FFCD2413U 06/18 © 2018 Electrolux Home Products, Inc.