Frigidaire FFCD2418US Installation Instructions - Page 2
Finishing the Drain - parts
View all Frigidaire FFCD2418US manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Leveling Dishwasher 5 within Cabinets 1. Measure height of cabinet opening from underside of countertop to floor. Check chart for height opening and suggested adjustment. Leg Leveler Adjustment Chart Height of Cabinet Opening Number of Turns to Adjust Levelers 34" (86.4cm) 0 341/8" (86.7cm) 2 345/16" (87.2cm) 6 341/2" (87.6cm) 9 For additional height add shims under levelers. 2. Move dishwasher to front of installation area. 3. Loosen the front and rear leveling legs by turning counterclockwise. Refer to chart for number of turns. See Figure 8. Front levelers should allow 1/4" below underside of countertop. 5/32" Socket 5/32" Socket Front Leveler Figure 8 15/16" Wrench Rear Leveler 4. If levelers have to be removed, make sure floor is free of obstructions. 5. Place dishwasher inside cabinet area so that it is centered in opening. Use caution when moving dishwasher to prevent damage to dishwasher, floor, and cabinets. 6. Remove lower rack to check that dishwasher is level from side to side by placing a level on the bottom of the inner door. See Figure 9a. Figure 9a Figure 9b 7. Remove lower rack to check that dishwasher is level from front to back by placing the level at the bottom of the tub at the lower rack wheel support. See Figure 9b. 8. Adjust levelers up or down until dishwasher is level. Finishing the Drain 6 Connection Electric Shock Hazard Plumbing material and drain hose must not come in contact with wiring or electrical components. Failure to follow this warning could result in personal injury from exposed wiring. 1. Pull out unit and check to see if drain hose is correctly attached to the drain pump assembly. If drain hose is not attached to drain pump, follow the instruction sheet (included with drain hose) on how to correctly install the drain hose to the drain pump assembly. 2. Move unit back in place while routing drain hose through access hole. Use caution to prevent damage to the dishwasher, floor and cabinets. IMPORTANT: Make sure there are no sharp bends or kinks that might restrict drain flow. 3. Secure drain hose to sink drain, disposer, or separate trap with a clamp. IMPORTANT: Be careful not to overtighten clamp or you may damage end of hose. Do not connect hose to horizontal pipe between sink drain and disposer. 4. Be sure unit does not rest on drain hose. It should be free of electrical components and door springs. Do not cut corrugated drain hose. Pull excess through cabinet and place under sink. Make sure hose does not come in contact with any sharp edges. See Figure 10. Sink at Left Connector 32" Clamp Remove knockout plug in disposer Pump Motor Figure 10 The drain hose loop must be at least 32" high from the floor to insure proper drainage. Finishing the Water 7 Connection Property Damage Do not solder within 6" of the water inlet valve. Damage to the plastic parts in the valve may occur. Use care that no sealer, dirt, or other objects enter the valve. Damage to the filter screen may occur. Be sure the dishwasher is placed where the water inlet valve will be kept from freezing. If the valve freezes, it may rupture and flooding may occur. Water Line 1. Flush water line before connecting it to water inlet valve to prevent early clogging of filter screen. Place a bunched towel over end of line to prevent splashing. Open water supply valve for a few seconds and let water drain into a pan. Turn off water supply at shut-off valve. Figure 11 Through Wall Through Cabinet Through Floor 2. Route water line to water inlet valve as shown in Figure 11. 3. While firmly pulling water supply line into 90° elbow, tightly connect water supply to water inlet valve. Supply line must be free of kinks, scales, chips, and lubricants. 4. Turn on water supply and check for leaks. 5. If water inlet valve clogs, make sure water supply is off. If using a 3/8" NPT valve,remove four (4) screws at inlet end of valve and clean filter screen. If using 3/4" hose thread fitting simply clean filter screen. Finishing the Electrical 8 Connection Electric Shock Hazard Make sure electrical power has been disconnected at fuse box or circuit breaker box. The dishwasher must be connected to a grounded metal, permanent wiring system. The equipment-grounding conductor must be run with the circuit conductors and connected to the appliance's equipment grounding terminal or lead. It is the consumer's responsibility to contact a qualified installer to make sure the electrical installation conforms with the National Electrical Code and local codes and ordinances. Do not connect the dishwasher to the power supply until the appliance is permanently grounded. All wiring connections must be enclosed in the junction box. This unit has copper lead wires. Joining aluminum building wire to stranded copper wire should be done by a qualified electrician using materials recognized by UL and local codes. Do not use an extension cord. Such use can result in fire, electrical shock, or other personal injury. Failure to follow these instructions could result in death or serious injury. Electrical Supply 1. Remove junction box cover and pull house wiring into junction box. See Figures 12 and 13. 2. Use a UL listed conduit connector,(not included), at box to stabilize wiring. IMPORTANT: Be sure electrical cable is not routed behind dishwasher's motor. Floor Anchoring This procedure is difficult and should be used only if countertop mounting brackets cannot be used. 1. Screw 1/4" lag screws, (not included), through holes provided in frame rail. See Figure 15. 2. Use expansion fasteners if floor is concrete. Before starting the dishwasher, Through Wall Through Cabinet Use 1/4" Lag Screws (not included) Figure 15 Through Floor Junction Box (in place) Figure 12 3. Inside junction box, attach ground wire under head of grounding screw and tighten. See Figure 13. 4. Connect incoming black lead to dishwasher's black lead and incoming white lead to dishwasher's white lead with wire nuts or other suitable connectors,(not included). Wire nuts should be tight. Note: If mounting your dishwasher to the countertop or to the floor is not a desirable option, you can order the side mount kit, 154806601/02, by contacting your dealer or parts supplier. This allows you to install the dishwasher by securing it to the cabinets or partitions on either side of the unit. The kit utilizes the front frame of the dishwasher to secure the unit to the cabinet or partitions. Removing & Replacing 10 Door Conduit Connector (not included) Ground Wire Electric Shock Hazard Disconnect electrical power at the fuse box or circuit breaker box before beginning installation. Failure to follow this warning could result in death or serious injury. White Wire to White Wire (Neutral) Black Wire to Black Wire (Hot) Figure 13 Junction Box Cover 10 Cut Hazard Metal color panels are sharp and should be handled with care. Wear gloves to protect hands. Failure to follow this warning may result in injury. 5. Replace junction box cover. See Figure 13. To Remove and Replace Outer Door Securing the Dishwasher 9 The dishwasher must be secured to keep it from tilting when door is opened. Choose one of the methods described below to secure unit. Countertop Anchoring 1. Install the Cabinet Seal Kit (Instructions included in Kit) 2. Replace Kickplate. See Figure 1 3. Adjust levelers (see Step 5) so mounting brackets touch underside of countertop. IMPORTANT: Dishwasher must rest on floor-do not hang from countertop. See Figure 14. 4. Tub needs to be even with the front of adjoining cabinets. 5. Screw mounting brackets firmly to countertop using screws provided in literature packet. 6. Open and close dishwasher door slowly. If door hits mounting brackets lower the dishwasher in front and rear. Note: Open and close door to make sure it does not hit surrounding cabinets or countertop. 1. Unlatch and open door. Using a Phillips head screw driver, remove two (2) screws from inner door. Save screws to reassemble. See Figure 16a. 2. Close and latch door while holding both sides. 3. Place one hand on each side of door and pull down at top approximately 1/4". Pull entire door assembly toward you to remove. See Figure 16b. Figure 16a Figure 16b Appearance of console and door may vary from your model. Use Phillips Head Screws # 8 x 5/8" (included in the literature packet). Figure 14 4. Place door where it will not get scratched or damaged while completing installation. 5. When ready to replace door, fit the slots on each side of top door edge over the tabs on the metal liner. Push on sides to insure the door is flat. Push up from bottom until there is no gap between door and console. See Figure 16c. Figure 16c Console Metal Liner Door Side View Appearance of console and door may vary from your model. 6. Unlatch door and open while supporting outer door on both sides at bottom to keep in place. Align screw holes and replace screws. Checking the Installation 11 check these items: Drain hose is assembled to drain pump. All packing materials and consumer literature have been removed from unit. Dishwasher is level and securely fastened. Open and close door to make sure it does not hit surrounding cabinet or countertop. Water and drain lines have no kinks. Wiring connections to junction box are tight. Water supply is turned on. Joints are free of leaks. Replacing Door 1. Refer to Step 10, numbers 5 and 6, for replacing outer door. 2. Adjust door springs to balance weight of door. A correct spring setting allows door to remain horizontal in opened position, yet will rise to close with slight lift of finger. 3. If necessary, increase tension by moving springs to a hole toward rear of unit or decrease by moving them toward front. 4. Turn electrical supply on. Operate the machine through at least one fill and pump-out, checking the following items: At first fill, make sure water completely covers filter surface. (Motor pump sound may be heard before water enters unit). At pump-out, make sure all water is pumped out. Check water connections again for leaks. Electric Shock Hazard If all connections are correct, there are no leaks, and unit runs properly, replace the kickplate assembly before placing unit into operation. Failure to follow this warning could result in electric shock.