Frigidaire FFET2725LB Complete Owner's Guide (English) - Page 15

SELF-CLEANING Self-Clean Cycle Time Length The Clean pads control the Self-Cleaning feature. If you are planning to use the oven directly after a self-clean cycle remember to allow time for the oven to cool down and the oven door to unlock. This normally takes about one hour. So a self-clean cycle will actually take about 4 hours to complete. To set the controls for a 3 hour Self-Cleaning cycle to start immediately and shut off automatically 1. Be sure that the clock is set with the correct time of day and the oven door is closed. 2. Press Clean pad. "3:00", "CLn" will appear, "UPPER" and "CLEAN" will flash in the display. The control will automatically clean for a 3 hour period. 3. Press Start pad. "DOOR" and "LOCKED" will flash; "UPPER" and "CLn" will appear in the display and the clock will return to the time of day. 4. As soon as the control is set, the motor driven oven door lock will begin to close automatically. Once the door has been locked the "UPPER", "DOOR" and "LOCKED" indicator light will stop flashing and remain on. Also, the oven icon will appear in the display. Allow about 15 seconds for the oven door lock to close. Note: If the optional delay Self-Clean is desired, finish steps 6-9. If Self-Clean is started immediately skip the remaining steps and continue with "When the Self-Clean cycle is completed". 5. Press Start time pad. "UPPER" and "DELAY" will start flashing and "- - - -" will appear in the display. 6. Press the Up or Down arrow pad until the desired start time appears in the display. 7. Press Start pad or wait 5 seconds. The display will return to the time of day. 8. The control will start the self-cleaning at the set start time, for the period of time previously selected. When the Self-Clean Cycle is Completed 1. Three long beeps will be heard and "CLn" will disappear from the display. "UPPER", "DOOR" and "LOCKED" will remain in the display until the door is unlocked. Some models will display "Hot". The cooling fan will continue to run until the oven has cooled down. 2. Once the oven has cooled down for 1 HOUR, and "UPPER", "DOOR" and "LOCKED" are no longer displayed, the oven door can then be opened. Stopping or Interrupting a Self-Cleaning Cycle If it becomes necessary to stop or interrupt a selfcleaning cycle due to excessive smoke or fire in the oven: 1. Press Clear off pad. 2. Once the oven has cooled down for approximately 1 hour and "UPPER", "DOOR" and "LOCKED" are no longer displayed, the oven door can then be opened. Important Notes when using the Self-Clean Feature: 1. A Self Clean cycle cannot be started if Oven Lockout feature is active. 2. When Self-Clean cycle is active on one oven, the other one cannot be used or set for a Self-Clean cycle or any cooking cycle. 3. If your clock is set for normal 12 hour display mode the delay Self-Clean can never be set to start more than 12 hours in advance. To set for a delayed Self-Cleaning cycle 12-24 hours in advance see instructions to set control for the 24 hour time of day display mode. Adjusting the Oven Temperature The temperature in the oven has been preset at the factory. When first using the oven, be sure to follow recipe times and temperatures. If you think the oven is too hot or too cool, the temperature in the oven can be adjusted. Before adjusting, test a recipe by using a temperature setting that is higher or lower than the recommended temperature. The baking results should help you to decide how much of an adjustment is needed.  NOTE ● The oven temperature adjustments made with this feature will not change the Self-Clean cycle temperature or the Broil temperature. ● Each oven may be adjusted individually. To adjust the oven temperature: 1. Press and hold Bake pad for 6 seconds. The preset adjustment number will appear and "UPPER" will flash in the display. 2. To increase the temperature use the Up arrow pad to enter the desired change. The temperature may be increased as much as 35°F (19°C). To decrease the temperature use the Down arrow pad to enter the desired change. The temperature may be decreased as much as 35°F (19°C). 3. Press Start pad or wait 5 seconds to accept the temperature change and the display will return to the time of day. Press Clear off pad to reject the change if necessary. 15