Frigidaire FFRP092LT6 Product Specifications Sheet - Page 3
Rearward Slope
View all Frigidaire FFRP092LT6 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
WAWAddaaaallllppSStteelleerr eevvee Packaged Terminal Air Conditioner (PTAC) FFRP092LT6 Air Conditioner / Electric Heater RReeaarrwwaarrdd SSllooppee 11//44"" SSllooppee FFrroonntt PPaanneell Accessory Wall Sleeve AccessoAOAOrccyuuccttddee-oossoossoorr rrGGyyrriillllee Outdoor Grille AWAWccaacclleell ssSSsslleeooeerryyvvee Chassis Front Panel CChhaassssiiss OOuuttssiiddee WWaallll IInnssiiddee WWaallll Plug Type (NEMA) 7-20P Product Dimensions Height Width Depth (Overall Unit) Depth (Inside Sleeve) Max. Wall Thickness 16" 42" 21-3/4" 13-3/4" 13-1/2" Wall Cutout Dimensions Height Width 16-1/4" 42-1/4" PTAC Specifications • Product Shipping Weight (approx.) - 137 Lbs. • An electrical supply with grounded three-prong receptacle is required. The power supply circuit must be installed in accordance with current edition of National Electrical Code (ANSI/NFPA 70) and local codes & ordinances. • Voltage Rating - 265V / 60 Hz • Amps @ 265V Volts = (Cool) 3.3 Amps / (Electric Heater) 13.1 Amps • Always consult local and national electric codes. • Recommended Circuit Breaker - 20 Amps • Unit equipped with 265V 3-wire power supply cord, NEMA plug type 7-20P, approximately 28" long. • In order for condensate water to drain properly inside the unit, the sleeve must be installed properly: Level from right to left with a slight 1/4" rearward pitch from the indoor side to the outdoor side as shown in the illustration above. Refer to the Installation Instructions on the web. • The drain kit listed on the Frigidaire® PTAC Accessories page can be used for an internal or external drain. This applies to new and replacement installation. Replacement Installation • When replacing existing PTAC with new unit, refer to Product Installation Guide on web to identify existing wall-sleeve manufacturer and size compatibility. If proper installation and slope are suspect, then correct installation of Frigidaire® PTAC Sleeve options recommended. • For any sleeve retrofit application, be sure that the foam seals (factory-installed on the tube sheets) provide a good seal between the grille and the outdoor coil tube sheets. These foam seals provide a barrier that stops air from the inside mixing with air on the outside (known as air recirculation). • Using Frigidaire® wall sleeve with Non-Frigidaire grille requires installation of an Accessory Baffle Kit, which ensures a good seal between the unit and exterior grille to prevent air recirculation. Air recirculation is a large contributor to performance loss and premature damage to major components. Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions. *See Frigidaire® PTAC accessories pages attached for optional accessories. New Installation • For new installation, Frigidaire® PTAC Sleeves are available and recommended for proper installation. See accessories pages for sleeve options.* • Standard PTAC installation requires 13-1/2" maximum wall thickness, unless a wall sleeve is used. • If the PTAC unit protrudes more than 4", then it is suggested that it be installed with a subbase. See accessories pages for subbase options. USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FFRP092LT6 01/17 © 2017 Electrolux Home Products, Inc. Specifications subject to change.