Frigidaire FGCD2444SW Complete Owner s Guide - Page 4

FEATURES AT A GLANCE, Operating Instructions

Page 4 highlights

FEATURES AT A GLANCE Your dishwasher cleans by spraying a mixture of hot water and detergent through the spray arms against soiled surfaces. First, the dishwasher fills with water covering the filter area. Water is then pumped through the spray arms. Soil particles go through and across the filter and down the drain as the water is pumped out. This series of steps are repeated as needed. The number of water fills vary with the cycle being used. Cup Shelves Nozzle or Spray Arm Bowl Tines Top Rack Middle Spray Arm Serial Label (Located on Right) Lower Spray Arm Overfill Protector Detergent Dispenser Rinse Aid Lower Rack Silverware Basket Glass Trap Heating Element Features may vary according to model Operating Instructions Getting Started 1. Load Dishwasher (See Preparing and Loading Dishes). 2. Add detergent (See Dishwasher Dispenser & Detergents). 3. Add Rinse Aid, if needed (See Rinse Aid). 4. Close door to latch. 5. Select desired CYCLE (See Cycle Chart). The indicator light above the pad will glow when selected. 6. Select desired OPTION (See Energy Options). The indicator light above the pad will glow when selected. 7. Run hot water faucet nearest dishwasher until water is hot. Turn water off. 8. To start, press START/PAUSE pad. 4 NOTE If the dishwasher door is opened while the unit is running, the START/PAUSE pad must be pressed and the door shut immediately to return the unit to the selected cycle and option, this must happen within 10 minutes for the unit to continue the cycle. Wash Cycle Selections Cycle times are approximate and will vary with options selected. Hot water is necessary to activate dishwasher detergent and melt fatty food soils. An automatic sensor will check the incoming water temperature and, if it is not hot enough, the cycle will be lengthend for automatic water heating in the main wash and final rinse of all cycles. This happens even when HI-TEMP WASH option has not be selected. When HI-TEMP WASH is selected, an even higher temperature will be reached to handle heavier soil loads.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

4
FEATURES AT A GLANCE
Features may vary according to model
Heating Element
Glass Trap
Detergent Dispenser
Overfill Protector
Silverware Basket
Lower Rack
Serial Label
(Located on Right)
Top Rack
Nozzle or Spray Arm
Cup Shelves
Middle Spray Arm
Lower Spray Arm
Rinse Aid
Your dishwasher cleans by spraying a mixture of hot water and detergent through the spray arms
against soiled surfaces.
First, the dishwasher fills with water covering the filter area.
Water is
then pumped through the spray arms.
Soil particles go through and across the filter and down the
drain as the water is pumped out.
This series of steps are repeated as needed.
The number of
water fills vary with the cycle being used.
Bowl Tines
Wash Cycle Selections
Cycle times are approximate and will vary with
options selected.
Hot water is necessary to
activate dishwasher detergent and melt fatty
food soils.
An automatic sensor will check
the incoming water temperature and, if it is
not hot enough, the cycle will be lengthend
for automatic water heating in the main wash
and final rinse of all cycles.
This happens
even when HI-TEMP WASH option has not be
selected.
When HI-TEMP WASH is selected,
an even higher temperature will be reached to
handle heavier soil loads.
Operating Instructions
Getting Started
1.
Load Dishwasher (See Preparing and
Loading Dishes).
2.
Add detergent (See Dishwasher Dispenser
& Detergents).
3.
Add Rinse Aid, if needed (See Rinse Aid).
4.
Close door to latch.
5.
Select desired CYCLE (See Cycle Chart).
The indicator light above the pad will glow
when selected.
6.
Select desired OPTION (See Energy
Options).
The indicator light above the pad
will glow when selected.
7.
Run hot water faucet nearest dishwasher
until water is hot.
Turn water off.
8.
To start, press START/PAUSE pad.
NOTE
If the dishwasher door is opened while the
unit is running, the START/PAUSE pad must
be pressed and the door shut immediately
to return the unit to the selected cycle and
option, this must happen within 10 minutes
for the unit to continue the cycle.
°