Home » Frigidaire Manuals » Ranges » Frigidaire FGDS3065PF » Manual Viewer

Frigidaire FGDS3065PF Complete Owner's Guide - Page 8

GROUNDING INSTRUCTIONS con't, For models without factory-supplied power cord, Liquefied, Petroleum L

View all Frigidaire FGDS3065PF manuals

Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

IMPORTANT SAFETY INSTRUCTIONS GROUNDING INSTRUCTIONS (con't) This appliance allows for conversion to Liquefied Petroleum (L.P.) Gas. WARNING Avoid fire hazard or electrical shock. Failure to follow this warning may cause serious injury, fire, or death. For models without factory-supplied power cord: For personal safety, this appliance must be properly grounded. For maximum safety, the power cord must be plugged into an electrical outlet that is the correct voltage, is correctly polarized and properly grounded in accordance with local codes. Is the personal responsibility of the consumer to have the appropriate outlet with the correct, properly grounded wall receptacle installed by a qualified electrician. It is the responsibility and obligation of the consumer to contact a qualified installer to assure that the electrical installation is adequate and is in conformance with all local codes and ordinances. See the installation instructions packaged with this appliance for complete installation and grounding instructions. WARNING Personal injury or death from electrical shock may occur if the conversion to L.P. gas is not made by a qualified installer or electrician. WARNING Any additions, changes or conversions required in order for this appliance to satisfactorily meet the application needs must be made by a qualified technician. Conversion to L.P. Gas If L.P. conversion is needed, contact your local L.P. Gas provider for assistance. The L.P. conversion kit is provided with this appliance and is located on the lower rear (back side) panel of the range. Before installing the kit be sure to read the L.P. Installation Instructions and follow them carefully when making the installation. 8

Section	Page
Table of contents	1
Need Help?	2
Visit the Frigidaire web site at www.frigidaire.com	2
Read this Use & Care Manual	2
If You Received a Damaged Range...	2
Save Time and Money	2
Product Registration	2
Record model & serial numbers here	2
Serial Plate Location- Left side of oven frame	2
Questions?	2
Product Record and Registration	2
CAUTIONS AND WARNINGS	3
IMPORTANT INSTRUCTIONS FOR USING YOUR OVEN	6
IMPORTANT INSTRUCTIONS FOR CLEANING YOUR OVEN	7
SELF-CLEANING OVENS	7
GROUNDING INSTRUCTIONS	7
GROUNDING INSTRUCTIONS (con’t)	8
Control locations of the gas surface burners	9
Assembly of the burner caps and burner grates	9
Double Ring style burners (some models)	10
Using Proper Cookware	11
Cookware Material Types	11
Operating the gas surface controls	12
Setting proper surface burner flame size	12
Setting Surface Controls	13
Home Canning	13
Setting Double Ring Burner (some models)	14
Oven vent location	15
Figure 14: Do not block oven vent location	15
Removing, replacing, and arranging flat or offset oven racks	15
Air circulation in the oven	15
Type of oven racks	16
Figure 15: Variety of oven racks	16
Effortless™ Oven Rack system	17
1. Locate all required parts. You will need the supplied oven rack. Effortless™ Oven Rack is a flat rack with a special dark coating on the left and right rack sides and the two supplied chrome connector arms.	17
2. Be sure the oven is completely cool before proceeding. Open the oven door.	17
3. Place the oven rack in positions 1,2, or 3 (see Figure 16 to verify positions)..	17
Figure 16: Rack positions	17
Figure 17: Bracket must be at rear of the range	17
Figure 18: Assembly of the Effortless™ oven rack	17
4. Assemble one connector arm at a time. With the oven door open and the oven rack in place, install one end of the connector arm to the hole in the door connector bracket (Figure 18) and the other end in the hole in the rack connector bracket (Figur...	17
Figure 19: Connector arm/door connection	18
5. While holding the connector arm in place, twist the connector arm so the ends of the connector arm point upwards (See Figure 20). The connector arm should now be locked into position.	18
6. Repeat steps 4 and 5 for the other connector arm.	18
Figure 20: Left & right brackets, pointing up	18
7. Once both connector arms are properly in place, be sure to test the oven rack operation by gently closing the oven door. The oven rack should move in and out of the oven freely when the door is opened or closed. (See Figure 21)	18
Figure 21: Effortless™ oven rack after assembly	18
Maximum and minimum time and temperature settings	20
Setting the Clock	20
Setting 12 or 24 Hour Time of Day Display	20
Setting Continuous Bake or 6 Hour Energy Saving	21
Temperature Display (Fahrenheit/Celsius)	21
Setting Control for Silent Operation	21
Setting the Timer	21
Setting Oven Lockout Feature	22
Oven Light	22
Setting Preheat	22
Setting Bake	23
Setting Bake Time	24
Setting Delay Start	24
Convection Cooking	25
Setting Convection Bake	25
Setting Convection Convert	26
Setting Convection Broil (some models)	26
Setting Convection Roast	27
Setting My Favorites Recipe (some models)	27
Setting Broil	28
Setting Slow Cook (some models)	29
Setting Warm/Keep Warm	29
Cooking with Meat Probe	30
Setting Warmer Drawer (some models)	32
Warmer Drawer Temperature Selection	33
Arranging Warmer Drawer Rack Positions	33
Restoring Factory Default Setting	34
Adjusting Oven Temperature	34
Setting the Sabbath Feature (For use on the Jewish Sabbath and Holidays)	35
Steam Clean	36
Self-Cleaning Operation	37
Setting Self Clean Cycle Duration	38
Setting a Delay Start Self Clean Cycle	39
Cleaning Various Parts of Your Oven	40
Cleaning the cooktop and surface burners	41
Replacing the oven light	41
Removing the Warmer Drawer	42
Removing and Replacing the Oven Door	43
Solutions to Common Baking Problems	44
Solutions to Common Problems	45