Frigidaire FGDS3065PF Installation Instructions - Page 11

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS (Models with an Electric Oven and a Gas Cooktop) 8 Moving the Appliance for Servicing and Cleaning Turn off the range line fuse or circuit breakers at the main power source, and turn off the manual gas shut-off valve. Make sure the range is cold. Remove the service drawer (warmer drawer on some models) and open the oven door. Lift the range at the front and slide it out of the cut-out opening without creating undue strain on the flexible gas conduit. Make sure not to pinch the flexible gas conduit at the back of the range when replacing the unit into the cutout opening. Replace the drawer, close the door and switch on the electrical power and gas to the range. 9 Range Installation Important Note: Door removal is not a requirement for installation of the range, but is an added convenience. Refer to the Use and Care Guide for oven door removal instructions. Figure 12 9.1 The range cooktop overlaps the countertop at the sides and the range rests on the floor. The cooktop is 31 1/2" (80 cm) wide. 9.2 Install base cabinets 30" (76,2 cm) apart. Make sure they are plumb and level before attaching cooktop. Shave raised countertop edge to clear 31 1/2" (80 cm) wide range top rim. 9.3 Install cabinet doors 31" (78,7 cm) min. apart so it will not interfere with range door opening. 9.4 Cutout countertop exactly as shown on page 3. For models equipped with Leveling Device: 9.5 Make sure the front leveling legs and the rear leveling device are setup higher than the height of the cabinet. 9.6 Install the anti-tip bracket at this point before placing the range at its final position. Follow the installation instructions on page 16 or on the anti-tip bracket template supplied with the range. 9.7 To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. 9.8 To reduce the risk of damaging your appliance, do not handle or manipulate it by the cooktop or control console. Manipulate with care. 9.9 Position range in front of the cabinet opening. 9.10 Make sure that the cooktop which overhangs the countertop clears the countertop. If necessary, raise the unit by lowering the leveling legs. 9.11 Slide the range into the cutout opening and center it before leveling it. 9.12 Level the range (see section 10). The floor where the range is to be installed must be level. Follow the instructions under "Leveling the Range- Models Equipped with Leveling Device". 9.13 Adjust leveling legs so that the underside of the cooktop is sitting on the countertop. Carefully screw in (refer to Leveling the range: Models equipped with Leveling Device") the back leveling leg until the cooktop overhang touches slightly the countertop. Then carefully screw in the front two leveling legs until the cooktop overhang touches slightly the countertop. For models equipped with Leveling Leg only (no leveling device): 9.5 Make sure the four leveling legs (front and rear) are setup higher than the height of the cabinet. 9.6 Install the anti-tip bracket at this point before placing the range at its final position. Follow the installation instructions on page 17 or on the anti-tip bracket template supplied with the range. 9.7 To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur. 9.8 To reduce the risk of damaging your appliance, do not handle or manipulate it by the cooktop. Manipulate with care. 9.9 Position range in front of the cabinet opening. 9.10 Make sure that the cooktop which overhangs the countertop clears the countertop. If necessary, raise the unit by lowering the leveling legs. 9.11 Level the range (see section 10). The floor where the range is to be installed must be level. Follow the instructions under "Leveling the Range-Models Equipped with Leveling Legs". 9.12 Slide the range into the cutout opening. 11