Frigidaire FGEW276SPF Installation Instructions - Page 4

Model and Serial Number Location, Oven Door Opening Reversal, Procedure

Page 4 highlights

ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS (and Optional Electric or Gas Cooktop Combination) Cable from Power Supply White Wire (Neutral) Red Wires Black Wires Junction Box Ground Wire (Bare or Green Wire) White Wire (Neutral) U.L.-Listed Conduit Connector (or CSA listed) Cable from appliance Figure 2 3-WIRE GROUNDED JUNCTION BOX 5. Model and Serial Number Location The serial plate is located along the interior side trim of the oven and visible when the door is opened. When ordering parts for or making inquires about your oven, always be sure to include the model and serial numbers and a lot number or letter from the serial plate on your oven. Wall Oven Serial Plate Location If oven is used in a new branch circuit installation (1996 NEC), mobile home, recreational vehicle, or where local codes do not permit grounding through the neutral (white) wire, the appliance frame MUST NOT be connected to the neutral wire of the 4-wire electrical system. (see figure 3): 1. Disconnect the power supply. 2. Separate the green (or bare copper) and white appliance cable wires. 3. In the junction box: connect appliance and power supply cable wires as shown in Figure 3. Figure 4 6. Oven Door Opening Reversal Procedure This wall oven can easily be modified to a left or a right hand opening. When you receive your appliance the door is set for a left opening. It is preferable to reverse door opening prior to the installation of the wall oven into the cabinet cavity. If wall oven is already installed, removed the anti-tip screws and then pull wall oven outward by approx. 2" (5 cm). Cable from Power Supply Ground Wire Red Wires White Wire Ground Wire (Bare or Green Wire) Junction Box Black Wires Cable from appliance White Wire U.L.-Listed Conduit Connector (or CSA listed) Figure 3 4-WIRE GROUNDED JUNCTION BOX 6.1 To remove the oven door from the appliance Be sure the oven door is closed. 6.1.1. Unscrew and remove the threaded pin from the lower hinge (See A, Figure 5). Figure 5 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28

4
ELECTRIC WALL OVEN INSTALLATION INSTRUCTIONS
(and Optional Electric or Gas Cooktop Combination)
5. Model and Serial Number Location
The serial plate is located along the interior side trim of
the oven and visible when the door is opened.
When ordering parts for or making inquires about your
oven, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your oven.
If oven is used in a new branch circuit installation
(1996 NEC), mobile home, recreational vehicle,
or where local codes DO NOT permit grounding
through the neutral (white) wire, the appliance
frame MUST NOT be connected to the neutral wire
of the 4-wire electrical system. (see figure 3):
1. Disconnect the power supply.
2. Separate the green (or bare copper) and white
appliance cable wires.
3. In the junction box:
connect appliance and power supply cable wires as
shown in Figure 3.
Figure 3
4-WIRE GROUNDED JUNCTION BOX
Cable from Power Supply
White Wire
Junction
Box
Cable from
appliance
White
Wire
Black
Wires
Red
Wires
Ground
Wire
Ground Wire
(Bare or
Green Wire)
U.L.-Listed
Conduit
Connector (or
CSA listed)
Figure 2
3-WIRE GROUNDED JUNCTION BOX
Cable from Power Supply
Black
Wires
Junction
Box
Cable from appliance
Ground Wire
(Bare or Green Wire)
White Wire
(Neutral)
U.L.-Listed Conduit
Connector (or CSA
listed)
Red
Wires
White Wire
(Neutral)
6. Oven Door Opening Reversal
Procedure
This wall oven can easily be modified to a left or a right
hand opening. When you receive your appliance the
door is set for a left opening. It is preferable to reverse
door opening prior to the installation of the wall oven
into the cabinet cavity. If wall oven is already installed,
removed the anti-tip screws and then pull wall oven
outward by approx. 2” (5 cm).
6.1 To remove the oven door from the
appliance
Be sure the oven door is closed.
6.1.1. Unscrew and remove the threaded pin from the
lower hinge (See
A
, Figure 5).
Figure 4
Wall Oven
Serial Plate
Location
Figure 5