Frigidaire FGGF3032MW Installation Instructions (All Languages) - Page 9

INSTALLATION INSTRUCTIONS - FREESTANDING GAS RANGE 7 Check ignition of surface burners. Operation of electric igniters should be checked after range and supply line connectors have been carefully checked for leaks and range has been connected to electric power. a. To check for proper ignition, push in and turn a surface burner knob counterclockwise to the LITE position. You will hear the igniter sparking. b. The surface burner should ignite when gas is available to the burner. Purge air from supply lines by leaving knob in the LITE position until burner ignites. Each burner should light within four (4) seconds in normal operation after air has been purged from supply lines. c. Visually check that burner has a flame. Once the burner ignites, the control knob should be turned out of the LITE position. d. Try each surface control knob separately until all surface burners have been checked. Each burner location is equipped with a separate electrode. 8 Adjust the LOW setting of surface burner valves (linear flow). Test to verify if LOW setting should be adjusted: a. Push in and turn control to LITE until burner ignites. b. Push in and quickly turn knob to lowest position. c. If burner goes out, reset control to OFF. d. Remove the surface burner control knob. For all burner styles (except Dual or Twin burner): e. Insert a thin-bladed screwdriver into the hollow valve stem and engage the slotted screw inside. Flame size can be increased or decreased with the turn of the screw. Turn counterclockwise to increase flame size. Turn clockwise to decrease flame size. (See Figs. 17 & 19). Adjust flame until you can quickly turn knob from LITE to lowest position without extinguishing the flame. Flame should be as small as possible without extinguishing. For Dual or Twin burner style adjustment only: e. The inner portion (Simmer) of the twin burner flame size can be increased or decreased with the turn of screw A. Use screw B to adjust the flame size of the outer portion of the Twin Burner (See Fig. 18). Turn the screw counterclockwise to increase flame size. Turn clockwise to decrease flame size. Adjust flame size until you can quickly turn the knob from LITE to lowest position without extinguishing the flame. Note: Air mixture adjustments are not required on surface burners. A B other surface burners Fig. 17 for Dual or Twin burner only Fig. 18 Burner flame size 5/8" Cooktop Fig. 19 9 Check ignition of oven burners. The operation of oven igniters should be checked after range and supply line connectors have been carefully checked for leaks and range has been connected to electric power. Be sure all packing materials and literature are removed from oven. The oven burner is equipped with an electric control system as well as an electric oven burner igniter. If your model is equipped with an upper oven burner, it will also have an electric burner igniter. These control systems require no adjustment. When the oven is set to operate, current will flow to the igniter. It will "glow" similar to a light bulb. When the igniter has reached a temperature sufficient to ignite gas, the electrically controlled oven valve will open and flame will appear at the oven burner. There is a time lapse from 30 to 60 seconds after the thermostat is turned ON before the flame appears at the oven burner. When the oven reaches the set temperature, the glowing igniter will cycle off. The burner flame will turn off in 20 to 30 seconds after the igniter turns off. To maintain any set oven temperature, this cycle will continue as long as the oven control is set to operate. To check oven burner ignition: a. Set oven to Bake at 300ºF. See User's Manual for operating instructions. b. Within 60 seconds the oven burner should ignite. Check for proper flame, and allow the burner to cycle once. Reset control to OFF. c. If your model is equipped with a waist-high broiler, set oven to Broil. See User's Manual for operating instructions. d. Within 60 seconds the broil burner should ignite. Check for proper flame. Reset control to OFF. 9