Frigidaire FGHD2465NF Wiring Diagram (English) - Page 2

SERVICE DATA SHEET This information is intended for use by persons having electrical and mechanical training and a level of knowledge of these subjects generally considered acceptable in the appliance repair trade. Electrolux Home Products North America cannot be responsible, nor assume any liability, for injury or damage of any kind arising from the use of this Service Data Sheet. P/N: 154889701 Electronic Series Color Code BK Black BU Blue PK Pink R Red R-BK......Red/Blk W White Y-BK..Yellow/Blk Operation To start Close and latch door. Press START/CANCEL pad. To delay start Close and latch door. Press DELAY START pad to select desired delay time. To select a new Press desired cycle and/or option pad. The indicator cycle or option lights will change. Press START/CANCEL within 15 seconds to begin cycle. To cancel cycle Press START/CANCEL. Dishwasher will drain for For controls 90 seconds, then shut off. lock Press and hold the RINSE ONLY or AIR DRY pad for 3 seconds. To unlock, press and hold the RINSE ONLY or AIR DRY pad for 3 seconds. Display Codes (Readout) PF..........A power failure has occurred Hd or HO.........Water heating delay CL..........Close and latch the door ER/ER....Switch Failure ER/CE....Configuration Error ER/uo.....Vent will not close ER/uF.....Fan not running '01-24'...Hour(s) delay before Start (some models) Water/Service Test STEP TOTAL TIME (SEC) WATER VALVE CIRCULATION MOTOR DRAIN MOTOR HEATER DISPENSER FAN UNIT WASHING LED SANITIZED LED DRYING LED CLEAN LED SENSING LED RINSE LED Device being monitored Display flashes when Detection of failure To activate Water/Service Test place unit in Power Failure or Idle Mode and the press"DRY or "AIR DRY"(model dependent) and the START/CANCEL keys for 3 seconds. The dishwasher will then step through the test cycle per the chart, if at any time, the START/ CANCEL key is pressed, the current step is terminated, while the test sequence advances to The next cycle step. 1 FILL/DISPENSER 60 1 0 0 0 1 0 1 0 0 0 1 0 Fan Damper Uo 2 FILL 27 1 0 0 0 0 0 1 0 0 0 1 0 Turbidity Tu 3 WASH/HEAT/DISP. 45 0 1 0 1 1 0 1 0 0 0 1 0 Hall Sensor HS 4 PAUSE 0.4 0 0 0 1 0 0 1 0 0 0 1 1 5 WASH/HEAT 75 0 1 0 1 0 0 0 0 0 0 0 1 6 WASH/HEAT/DISP. 60 0 1 0 1 1 0 0 0 0 0 0 1 Thermistor Th 7 DRAIN 90 0 0 1 0 0 1 0 0 0 0 0 0 Fan Speed UF 8 DRY 90 0 0 1 X 0 1 0 0 1 0 0 0 Rinse Aid RA TOTAL 447 0101 0 0 X - denotes selectable option CLEAN LED stays on until door is opened or cycle is started. Cycle Selection Options Display Codes (LED) SENSING Turbidity sensor is checking the condition of the wash/rinse water. No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL. WASHING Wash portion of cycle. SANITIZED The SANITIZED criteria has been met. Indicator light will switch off when door is opened. DRYING Drying portion of cycle. CLEAN Shows completion of cycle. Indicator light will switch off when door is opened. OPTION LED's Flashing -- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing (Some models) indicates power failure has occurred. Press START/CANCEL pad and Wiring Diagram