Frigidaire FGID2479SF Product Specifications Sheet - Page 3
Front, Right - gallery dishwasher
View all Frigidaire FGID2479SF manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
24" Built-In Dishwasher w/Integrated Controls (IC) w/Stainless Tub (ST) Gallery (Q, R & S Models) Dishwasher FGID2479SF 24" Built-In Front 23 3/4" Left 24 1/4" Right 50 1/4" 22 1/2" 33 3/4" Adjustable to 35 3/4"* Door in 90° open position 27 3/4" *Height only adjustable to 35 3/4" max. when installed in 35 3/4" max. standard cabinetry cutout. (Dimensions do NOT include insulation - insulation blanket may be compressed during installation.) Power supply & water inlet location (bottom rear) 3 1/2" min.to 4 1/2" max. 90° 34" min. to 35 3/4" max.** 24" min. 3" 90° Electrical, water, and drain lines must be confined to shaded area Preferred drain areas 3" 18" 3" **NOTE: 35 3/4" max. height for standard cabinetry cutout. 11/4" (5/16" min. clearance required from unit to 1" 21/4" underside of countertop.) 21/4" 24" Dishwasher Specifications • Product Shipping Weight (approx.) - 91 Lbs. • Voltage Rating - 120V / 60 Hz / 15 Amps (maximum 20 Amps if connected with disposer) • Connected Load (kW Rating) @ 120 Volts = 1.44 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120V = 15 Amps • Always consult local and national electric & plumbing codes. Meets requirements of ASSE 1006 - integral air gap on supply. • Water Pressure - Hot water line to dishwasher must provide between 20 and 120 pounds per square inch (psi) with at least 120° F hot water temperature. • Make sure location has correct drain, water and electrical outlets to make connections - MUST be confined to shaded areas. • Electrical and water supplies should enter cabinet opening on floor, or through back or side walls, as shown in shaded areas. • Keep back free of drain, water & electrical supply. • Connections preferably located toward left side of dishwasher. Do not cross drain, water or electrical lines in front of motor, blower or frame. • If connecting drain hose to sink trap, local code may require installation of Air Gap Kit (not included). • Leveling legs supplied to adjust height. (Note: Height only adjustable to 35-3/4" max. when installed in 35-3/4" max. standard cabinetry cutout. 5/16" min. clearance required from top of unit to underside of countertop. Dimensions do NOT include insulation - insulation blanket may be compressed during installation.) • When installing adjacent to wall, cabinet or other obstruction that extends beyond front edge of unit, allow 2" minimum clearance between opened door and obstruction. • Floor should be flat and free of obstructions with carpet removed to provide motor clearance. • When installing at end of cabinet line, sides and back must be fully enclosed. • Do not install unit under a cooktop, damage will occur. • Recommended to seal cabinets, enclosing all sides of dishwasher, including underside of countertop, with oil-based paint or moistureproof polyurethane to prevent possible steam/moisture damage. Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions. USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FGID2479S 03/17 © 2017 Electrolux Home Products, Inc. Meets requirements of ASSE 1006 Specifications subject to change.