Frigidaire FGIF3036TD Complete Owner s Guide - Page 31
To set a self clean cycle, Adjusting the oven temperature
View all Frigidaire FGIF3036TD manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 31 highlights
To set a self clean cycle: 1. Press Self Clean. --- appears in the display. 2. Press until 3:00 appears in the display for a 3 hour self clean process, or push until 2:00 appears in the display for a 2 hour self clean process. 3. As soon as the controls are set, the motor driven lock will begin to close automatically and the door locked indicator light will flash. Do not open the oven door while the light is flashing (allow about 15 seconds for the oven door to lock). 4. CLn will appear in the display during the self clean cycle, and the door locked light will glow until the self cleaning cycle is complete or cancelled and the oven temperature has cooled. When the self clean cycle has completed: • The time of day will appear in the display window, and the Clean key and door locked light will continue to glow. • Once the oven has cooled down for about 1 hour and the door locked light has gone out, the oven door may be opened. • To avoid possible burns, use care when opening the oven door after the self cleaning cycle. Stand to the side of the oven when opening the door to allow hot air or steam to escape. To stop or interrupt a self clean cycle (once it has been activated): 1. Press OFF. 2. Once the oven has cooled down for about 1 hour and the door locked light has turned off, the oven door can be opened. 3. Restart the self clean cycle once all conditions have been corrected. Setting Delay Start Self Clean To start a delay self clean with default clean time of 3 hours and a start time of 9:00 o'clock: Be sure the clock is set with the correct time of day, the oven is empty, and all oven racks are removed. Be sure oven door is completely closed. 1. Press Start Time and to 9 0 0 and release key. 2. Press Self Clean. --- appears in the display. 3. Press until 3:00 appears in the display for a 3 hour self clean process, or push until 2:00 appears in the display for a 2 hour self clean process. SETTING OVEN CONTROLS 4. The motor driven lock will begin to close automatically and the door locked indicator light will flash. Do not open the oven door while the light is flashing (allow about 15 seconds for the oven door to lock). 5. CLn will appear in the display during the self clean cycle, and the door locked light will glow until the self cleaning cycle is complete or cancelled and the oven temperature has cooled. Adjusting the oven temperature Your appliance has been factory calibrated and tested to ensure an accurate baking temperature. For the first few uses, follow your recipe times and temperature recommendations carefully. If you think the oven is cooking too hot or too cool for your recipe times, you can adjust the control so the oven cooks hotter or cooler than the temperature displayed. NOTE Do not use oven thermometers such as those found in grocery stores to check the temperature settings inside your oven. These oven thermometers may vary as much as 20 to 40 degrees from actual temperatures. To adjust oven temperature: 1. Press Bake. 2. Set the temperature to 550°F (287°C) by pressing and holding . 3. Within 3 seconds, press and hold Bake until numeric digit(s) appear. Release Bake key. The display now indicates the amount of degrees offset between the original factory temperature setting and the current temperature setting. If the oven control has the original factory calibration, the display will read 00. 4. The temperature can now be adjusted up or down 35°F (19°C), in 5°F (1°C) increments. Press and hold to adjust the temperature higher until the desired amount of offset appears in the display. When lowering the oven temperature using , a minus sign (-) will appear before the number to indicate that the oven will be cooler by the displayed amount of degrees. 5. When you have made the desired adjustment, press OFF to go back to the time of day display. 31