Frigidaire FMP330RGB Installation Instructions (English) - Page 11

Installation Instructions, WARNING - review

Get Frigidaire FMP330RGB - 18in Interior Portable Dishwasher PDF manuals and user guides
UPC - 012505110184
View all Frigidaire FMP330RGB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Installation Instructions STEP 13 CONNECT POWER SUPPLY Skip this step if equipped with power cord. Verify that power is turned off at the source. • Remove junction box cover "A". • Locate the three dishwasher wires, (white, black and green) with stripped ends. Insert dishwasher wires through the small hole in the junction box "B". • Secure house wiring to the bottom of the junction box with a strain relief "C". • User wire nuts to connect incoming ground to green, white to white and black to black "D". • Replace junction box cover "E". Check to be sure that wires are not pinched under the cover. WARNING If house wiring is not 2-wire with ground, a ground must be provided by the installer. When house wiring is aluminum, be sure to use UL Listed anti-oxidant compound and aluminum-to-copper connectors. STEP 14 PRE-TEST CHECKLIST Review this list after installing your dishwasher to avoid charges for a service call that is not covered by your warranty. … Check to be sure power is OFF. … Open door and remove all foam and paper packaging. … Locate the Owner's Manual in the literature package. … Read the Owner's Manual for operating instructions. … Check door opening and closing. If door does not open and close freely or tends to fall, check spring adjustments. See Step 1. … Check to be sure that wiring is secure under the dishwasher, not pinched or in contact with door springs or other components. See Step 9. … Check door alignment with tub. If door hits tub, level dishwasher. See Step 10. … Pull lower rack out, about half way. Check to be sure it does not roll back or forward on the door. If the rack moves, adjust leveling legs. See Step 10. … Check door alignment with cabinet. If door hits cabinet, reposition or relevel dishwasher. See Step 10. … Verify water supply and drain lines are not kinked or in contact with other components. Contact with motor or dishwasher frame could cause noise. See Step 8. … Turn on the sink hot water faucet and verify water temperature. Incoming water temperature must be between 120°F and 150°F. A minimum of 120°F temperature is required for best wash performance. See "Prepare Hot Water Line", page 5. … Add 2 quarts of water to the bottom of the dishwasher to lubricate the pump seal. … Turn on water supply. Check for leaks. Tighten connections if needed. … Remove protective film if present from the control panel and door. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
11
Installation Instructions
STEP 14 PRE-TEST CHECKLIST
Review this list after installing your dishwasher to
Review this list after installing your dishwasher to
Review this list after installing your dishwasher to
Review this list after installing your dishwasher to
Review this list after installing your dishwasher to
avoid charges for a service call that is not covered
avoid charges for a service call that is not covered
avoid charges for a service call that is not covered
avoid charges for a service call that is not covered
avoid charges for a service call that is not covered
by your warranty.
by your warranty.
by your warranty.
by your warranty.
by your warranty.
Check to be sure power is OFF.
Open door and remove all foam and paper packaging.
Locate the Owner’s Manual in the literature package.
Read the Owner’s Manual for operating instructions.
Check door opening and closing. If door does not open and
close freely or tends to fall, check spring adjustments. See
Step 1.
Check to be sure that wiring is secure under the dishwasher,
not pinched or in contact with door springs or other
components. See Step 9.
Check door alignment with tub. If door hits tub, level
dishwasher. See Step 10.
Pull lower rack out, about half way. Check to be sure it does
not roll back or forward on the door. If the rack moves, adjust
leveling legs. See Step 10.
Check door alignment with cabinet. If door hits cabinet,
reposition or relevel dishwasher. See Step 10.
Verify water supply and drain lines are not kinked or in
contact with other components. Contact with motor or
dishwasher frame could cause noise. See Step 8.
Turn on the sink hot water faucet and verify water
temperature. Incoming water temperature must be between
120°F and 150°F. A minimum of 120°F temperature is
required for best wash performance. See "Prepare Hot Water
Line", page 5.
Add 2 quarts of water to the bottom of the dishwasher to
lubricate the pump seal.
Turn on water supply. Check for leaks. Tighten connections
if needed.
Remove protective film if present from the control panel and
door.
STEP 13 CONNECT POWER
SUPPLY
Skip this step if equipped with power cord.
Skip this step if equipped with power cord.
Skip this step if equipped with power cord.
Skip this step if equipped with power cord.
Skip this step if equipped with power cord.
Verify that power is turned off at the source.
Verify that power is turned off at the source.
Verify that power is turned off at the source.
Verify that power is turned off at the source.
Verify that power is turned off at the source.
• Remove junction box cover “A”.
• Locate the three dishwasher wires, (white, black and green)
with stripped ends. Insert dishwasher wires through the
small hole in the junction box “B”.
• Secure house wiring to the bottom of the junction box with a
strain relief “C”.
• User wire nuts to connect incoming ground to green, white to
white and black to black “D”.
• Replace junction box cover “E”. Check to be sure that wires
are not pinched under the cover.
WARNING
If house wiring is not 2-wire with ground,
a ground must be provided by the installer.
When house wiring is aluminum, be sure to
use UL Listed anti-oxidant compound and
aluminum-to-copper connectors.