Frigidaire FPBM307NTF Product Specifications Sheet - Page 3

Installation Specifications, Microwave - professional microwave

Page 3 highlights

with Bottom Controls (FPBM3077R) PFMPIrCBoRMfO3eW 0s7ANsVTiEoF nal (1.8 Cu. Ft.) (new handle) 30" OVER-THE-RANGE Locate 120V/60Hz grounded outlet inside upper cabinet Microwave MUST be mounted to BOTH a top cabinet AND a wall* Bottom edge of cabinet MUST be 30" min. from cooking surface 66" min. from floor to top of microwave Rear Wall 30" min. 30" min. 2" min. 12" min. Cabinet MUST be 13" capable of max. supporting a total load of 135 lbs. Backsplash Blower plate allows for vertical or horizontal ducting Power cord location 17 9/16" *Can NOT be installed in island or peninsula cabinet arrangements rear extrusion 16 1/16" 29 7/8" lower extrusion Allow at least 26" clearance for door depth when open INSTALLATION SPECIFICATIONS • Product Shipping Weight (approx.) - 81 Lbs. • Voltage Rating - 120V / 60 Hz / 15 Amps • Connected Load (kW Rating) @ 120 Volts = 1.6 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120 Volts = 15 Amps • Always consult local and national electric codes. • Grounded outlet should be located in cabinet above, with hole in base to route power cord. Carefully follow top template instructions for power cord clearance when installing beneath smooth, flat cabinets. • Microwave's exhaust ventilation system is preset to recirculate air inside with no ducting system required. Exhausting air outside is optional, using either vertical or horizontal ducting system. (Refer to Ducted Option Specifications for outside ventilation.) • For safe and proper installation, microwave MUST be mounted to BOTH a top cabinet AND a wall, and connected to at least one wall stud. Can NOT be installed in island or peninsula cabinet arrangements. • Cabinet bottom MUST be level to insure proper installation. • Cabinet MUST be capable of supporting a total load of 135 lbs. • If the cabinet depth (including the cabinet doors) is more than 13" then the unit must be spaced out from the wall using adequate materials supporting 150 lbs. to allow proper top vent air exhaust. • Filler blocks recommended for installation when cabinet front hangs below recessed bottom shelf. • Minimum distance of 30" required from cooking surface to bottom edge of top cabinet. • Minimum distance of 66" required from floor to top of microwave. • Opening between cabinets MUST be 30" wide and free of obstructions. For openings up to 36" wide, order optional 36" Filler Panel Kit to fill in gap between unit and cabinets. • Allow 26" minimum clearance for 90° door swing. DUCTED OPTION SPECIFICATIONS • For outside ventilation. • Exhaust duct adapter will be needed for outside ventilation, to mate with standard 3-1/4" x 10" rectangular duct. If round duct required, rectangular-to-round transition adapter will be needed with no less than 6" diameter. • For most efficient airflow exhaust, use a straight run or as few elbows as possible with a maximum duct length of 3-1/4" x 10" rectangular or 6" diameter round duct, not to exceed 120 equivalent feet. • For horizontal installation, be sure to allow enough space between wall studs to accommodate exhaust. • Refer to installation instructions on web for detailed duct preparation and converting exhaust vent blower system for exterior exhaust ventilation. OPTIONAL ACCESSORIES • 36" Stainless Steel Filler Panel Kit - (PN # MWFILKTSS). Note: For planning purposes only. Always consult local and national electric, gas and plumbing codes. Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com. Specifications subject to change. Accessories information available on the web at frigidaire.com USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FPBM307NT 10/17 © 2017 Electrolux Home Products, Inc.

  • 1
  • 2
  • 3

INSTALLATION SPECIFICATIONS
Product Shipping Weight (approx.) – 81 Lbs.
Voltage Rating – 120V / 60 Hz / 15 Amps
Connected Load (kW Rating) @ 120 Volts = 1.6  kW
(For use on adequately wired 120V, dedicated circuit having 2-wire service
with a separate ground wire. Appliance must be grounded for safe operation.)
Amps @ 120 Volts = 15 Amps
Always consult local and national electric codes.
Grounded outlet should be located in cabinet above, with hole in base to
route power cord. Carefully follow top template instructions for power cord
clearance when installing beneath smooth, flat cabinets.
Microwave’s exhaust ventilation system is preset to recirculate air inside with
no ducting system required. Exhausting air outside is optional, using either
vertical or horizontal ducting system.
(Refer to Ducted Option Specifications
for outside ventilation.)
For safe and proper installation, microwave MUST be mounted to BOTH
a top cabinet AND a wall, and connected to at least one wall stud. Can NOT
be installed in island or peninsula cabinet arrangements.
Cabinet bottom MUST be level to insure proper installation.
Cabinet MUST be capable of supporting a total load of 135 lbs.
If the cabinet depth (including the cabinet doors) is more than 13” then the
unit must be spaced out from the wall using adequate materials supporting
150 lbs. to allow proper top vent air exhaust.
Filler blocks recommended for installation when cabinet front hangs below
recessed bottom shelf.
Minimum distance of 30” required from cooking surface to bottom
edge of top cabinet.
Minimum distance of 66” required from floor to top of microwave.
Opening between cabinets MUST be 30” wide and free of obstructions.
For openings up to 36” wide, order optional 36” Filler Panel Kit to fill
in gap between unit and cabinets.
Allow 26” minimum clearance for 90° door swing.
DUCTED OPTION SPECIFICATIONS
For outside ventilation.
Exhaust duct adapter will be needed for outside ventilation, to mate
with standard 3-1/4” x 10” rectangular duct. If round duct required,
rectangular-to-round transition adapter will be needed with no less
than 6” diameter.
For most efficient airflow exhaust, use a straight run or as few elbows
as possible with a maximum duct length of 3-1/4” x 10” rectangular or
6” diameter round duct, not to exceed 120 equivalent feet.
For horizontal installation, be sure to allow enough space between wall
studs to accommodate exhaust.
Refer to installation instructions on web for detailed duct
preparation and converting exhaust vent blower system for exterior
exhaust ventilation.
OPTIONAL ACCESSORIES
36” Stainless Steel Filler Panel Kit – (PN # MWFILKTSS).
Specifications subject to change.
Accessories information available on the web at
frigidaire.com
Note:
For planning purposes only. Always consult local and national electric, gas and plumbing codes.
Refer to Product Installation Guide for detailed installation instructions on the web at frigidaire.com.
USA
10200 David Taylor Drive
Charlotte, NC 28262
1-800-FRIGIDAIRE
frigidaire.com
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
1-800-265-8352
frigidaire.ca
FPBM307NT 10/17
© 2017 Electrolux Home Products, Inc.
12"
min.
13"
max.
2"
min.
Backsplash
Rear Wall
30"
min.
66"
min.
from floor to
top of
microwave
Bottom edge of
cabinet MUST be
30"
min. from
cooking surface
Cabinet MUST be
capable of
supporting a total
load of 135 lbs.
30"
min.
Microwave MUST
be mounted to
BOTH a top cabinet
AND a wall*
Locate 120V/60Hz grounded outlet inside upper cabinet
*Can NOT be installed
in island or peninsula
cabinet arrangements
29
7
/
8
"
17
9
/
16
"
16
1
/
16
"
Power cord
location
Allow at least 26" clearance
for door depth when open
lower
extrusion
rear
extrusion
Blower plate allows for vertical
or horizontal ducting
FPBM307NTF
MICROWAVE
30" OVER-THE-RANGE