Frigidaire FPEW3085KF Product Specifications Sheet (English) - Page 5

(excludes side swing wall oven) Electric Cooktop Installation Over 30"/27" Electric Single Wall Oven For all approved electric cooktop models, cut minimum 4" x 4" opening in right side filler panel, to route armored cable to junction box Side filler panels necessary to isolate oven from adjoining cabinets. Panel height may need to be modified to accommodate depth of approved electric cooktop models Electric Single Wall Oven Cutout For all 30" & 27" models † Cooktop cutout** Approx. 3" Approx. 3" 23 1/2 Plywood min.* 240 /208V base Junction box for wall oven A 240 /208V Junction box for electric cooktop Oven cutout 36" min. 27 1/4" min. 28 5/8" max. 24" min. cutout depth Install 3/4" full plywood base on 2 runners, flush with toe plate, capable of supporting 200 lbs. Unit will overlap cutout (minimum) edges by 1" Cutout Width (A) 4-1/2" maximum height allowed from oven base to floor if cooktop is installed directly over wall oven. To route armored cable to junction box, cut minimum 9" x 9" opening in wood base, 2" from left side filler panel. (5" maximum height allowed with no cooktop.) *Critical dimension - MUST be applied **For cooktop cutout dimensions refer to model-specific product page or installation guide on web 30" Wall Oven 27" Wall Oven 28 1/2" min. 29" max. 24 7/8" min. 25 1/4" max. †This installation drawing excludes model GLEB27Z7H with side-swing door 30"/ 27" Electric Single Wall Oven Under-Counter Installation Specifications • Single phase 3- or 4-wire cable, 120 / 240 or 120 / 208 Volt, 60 Hertz AC only electrical supply with ground required on separate circuit fused on both sides of line. • For detailed electrical requirements, refer to model-specific product page and installation guide on web. • Always consult local and national electric codes. • Minimum 21" clearance for oven door depth when open. • Minimum 23-1/2" deep cutout dimension is critical for proper installation, to ensure that oven's faceplate will fit flush against cabinet front. • Side filler panels necessary to isolate oven from adjoining cabinets. • Full oven base of solid plywood or similar material required, capable of supporting 200 Lbs. (30" models) or 150 Lbs. (27" models). Install over two runners and flush with toe plate. • Base must be level and cabinet front must be square. • Allow 5" maximum height from oven base to floor, if NO cooktop is installed directly over wall oven. Electric Cooktop Installation Over 30"/ 27" Electric Single Wall Oven Specifications All Frigidaire® Electric Single Wall Ovens are approved to be used beneath any approved Frigidaire® Electric Cooktop. (This installation page excludes approved wall oven model GLEB27Z7H. For modelspecific installation details, refer to Electric Cooktop Installation Over 27" Electric Single Wall Oven GLEB27Z7H Specifications pages on web.) For detailed Electric Cooktop installation, refer to model-specific product page and installation guide on web. • Side filler panel height may need to be modified to accommodate the depth of approved electric cooktop models. • To route armored cable to junction box, cut minimum 4" x 4" opening in right side filler panel. • Allow 4-1/2" maximum height from oven base to floor, if cooktop is installed directly over wall oven. Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions. USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca EC_EW INST FR 02/11 © 2011 Electrolux Home Products, Inc. Specifications subject to change. Printed in the U.S.A.