Frigidaire FPID2498SF Wiring Diagram - Page 2
Trouble Shooting Tips, Exploded View of Wash System - lowes
View all Frigidaire FPID2498SF manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
Exploded View of Wash System Tub Gasket The door gasket is pressed into the tub channel for an interference fit. To install the gasket: 1. Press the gasket across the header using your hands. 2. Press the gasket while stretching around the corners . NOTE: There should be no wrinkles or puckers in the corners. 3. Place the gasket end at the bottom and then press the gasket in from the bottom up. Trouble Shooting Tips Personal Injury Hazard Always disconnect the dishwasher from the electrical power source before adjusting or replacing components. Symptom Dishwasher will not operate when turned on. Check the Following Remedy 1. Fuse (blown or tripped). 2. 120 VAC supply wiring connection faulty. 3. Electronic control board defective. 4. No 12 VAC power to control. 5. Motor (inoperative). 6. Door switch (open contacts). 7. Door latch not making contact with door switch. 8. Touch pad circuit defective. 9. No indicator lamps illuminate when START or OPTIONS are pressed. 1. Replace fuse or reset breaker. 2. Repair or replace wire fasteners at dishwasher junction box. 3. Replace control board. 4. Replace control board. 5. Replace motor/impeller assembly. 6. Replace latch assembly. 7. Replace latch assembly. 8. Replace console assembly. 9. Replace console assembly. Motor hums but will not start or run. 1. Motor (bad bearings). 2. Motor stuck due to prolonged non-use. 1. Replace motor assembly. 2. Rotate motor impeller. Motor trips out on internal thermal overload protector. 1. Improper voltage. 2. Motor windings shorted. 3. Glass or foreign items in pump. 1. Check voltage. 2. Replace motor/impeller assembly. 3. Clean and clear blockage. Dishwasher runs but will not heat. 1. Heater element (open). 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Hi-Limit thermostat defective. 1. Replace heater element. 2. Replace control board. 3. Repair or replace. 4. Replace thermostat. Detergent cover will not latch or open. 1. Latch mechanism defective. 2. Electronic control board defective. 3. Wiring or terminal defective. 4. Broken spring(s). 5. Defective actuator. 1. Replace dispenser. 2. Replace control board. 3. Repair or replace. 4. Replace dispenser. 5. Replace dispenser. Dishwasher will not pump out. Dishwasher will not fill with water. 1. Drain restricted. 2. Electronic control board defective. 3. Defective drain pump. 4. Blocked impeller. 5. Open windings. 6. Wiring or terminal defective. 7. Defective Drain Valve. 1. Clear restrictions. 2. Replace control board. 3. Replace pump. 4. Check for blockage, clear. 5. Replace pump assembly. 6. Repair or replace. 7. Repair or replace. 1. Water supply turned off. 2. Defective water inlet fill valve. 3. Check fill valve screen for obstructions. 4. Defective float switch. 5. Electronic control board defective. 6. Wiring or terminal defective. 7. Float stuck in "UP" position. 1. Turn water supply on. 2. Replace water inlet fill valve. 3. Disassemble and clean screen. 4. Repair or replace. 5. Replace control board. 6. Repair or replace. 7. Clean or replace float. Dishwasher water siphons out. Product Specifications Electrical Rating 120 Volts, 60Hz Separate Circuit..15 amp min.- 20 amp max. Motor (Amps 0.8 Heater Wattage 850 Total Amps (load rated 13.0 Water Temps controlled 5°F To assure success have outer door in place TempAssure (cycle dependent) Main Wash: 140°F Final Wash: 140°F Hi-TempAssure: 140°F Wash/149°F Final Rinse SanitizeAssure: 140°F Wash/156°F Final Rinse Hi-Limit Thermostat 200°F (93°C) Water Supply Suggested minimum incoming water temperature 120°F (49°C) Pressure (PSI) min./max 20/90 Connection (GHT 3/4" 11.5NH Consumption (Normal Cycle 2.9 - 7.3 U.S. gal., 11.0 - 27.7 liters Water valve flow rate (U.S. GPM 0.66 Water recirculation rate (U.S. GPM approx. 17 (@2900rpm) Water fill time 104 sec. Detergent left in dispenser. 1. Drain hose (high) loop too low. 2. Drain line connected to a floor drain not vented. 3. Drain valve or pump stuck open. 1. Repair to proper 32-inch minimum height. 2. Install air gap at counter top. 3. Repair or replace. 1. Detergent allowed to stand too long in dispenser. 2. Dispenser wet when detergent was added. 3. Detergent cover held closed or blocked by large dishes. 4. Improper incoming water temperature to properly dissolve detergent. 5. Spray arm blocked. 6. Is water getting into unit. 1. Instruct customer/user. 2. Instruct customer/user. 3. Instruct customer/user on proper loading of dishes. 4. Incoming water temperature of 120°F is required to properly dissolve dishwashing detergents. 5. Instruct customer/user. 6. Check fill valve repair or replace. Note: See "Detergent cover will not latch or open." 808936687 -A 26/2016