Frigidaire FPMO209KF Product Specifications Sheet (English) - Page 2

Microwave Specifications, Optional Accessories - dimensions

Page 2 highlights

Professional and Gallery Microwave FPMO209K F Built-In Microwave Specifications • Product Shipping Weight (Approx.) - 46 Lbs. (not incl. Trim Kit) • Voltage Rating - 120V / 60 Hz / 15 or 20 Amps • Connected Load (kW Rating) @ 120 Volts = 1.7 kW (For use on adequately wired 120V, dedicated circuit having 2-wire service with a separate ground wire. Appliance must be grounded for safe operation.) • Amps @ 120 Volts = 14.3 Amps • Always consult local and national electric codes. • Microwave can stand alone on countertop or be built in with optional 30" or 27" Trim Kit (ordered by individual part number) which includes Bottom Duct Assembly - shipped in separate box. • Allow 21" minimum clearance for 90° door swing. • Minimum 20" deep oven cutout dimension is critical for proper installation for oven and faceplate to fit flush against cabinet front. • Consult local building code, in the event that cutout opening may be required to be enclosed with sides, ceiling and rear partition. • Full oven base of solid plywood or similar material required, capable of supporting 100 Lbs. • Base must be level and front of cabinet square for proper operation. • Grounded outlet should NOT be located in shaded area, as indicated, UNLESS cabinet depth is greater than 21". • Can NOT be installed above any gas wall oven. • Built-In Microwave is approved to be used in combination with any Frigidaire® Electric Single Wall Oven and /or Warmer Drawer. (Refer to model-specific Combination Installation Specification pages on web.) • When used in combination with another Frigidaire® built-in product, a minimum clearance of 2-7/8" required from bottom of Built-In Microwave cutout to top edge of companion product's faceplate, leaving a 2" visible gap between both product faceplates. Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions Optional Accessories • 30" Stainless Steel Trim Kit - (PN # MWTK30KF). • 27" Stainless Steel Trim Kit - (PN # MWTK27KF). FRIGIDAIRE® USA • 250 Bobby Jones Expressway • Martinez, GA 30907 • 1-800-FRIGIDAIRE • frigidaire.com CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca FPMO209K 04/10 © 2010 Electrolux Home Products, Inc. Specifications subject to change. Printed in the U.S.A.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6

Specifications
subject to change.
FRIGIDAIRE®
USA
250 Bobby Jones Expressway
Martinez, GA 30907
1-800-FRIGIDAIRE
frigidaire.com
CANADA
5855 Terry Fox Way
Mississauga, ON L5V 3E4
1-800-265-8352
frigidaire.ca
FPMO209K 04/10
© 2010 Electrolux Home Products, Inc.
Printed in the U.S.A.
Microwave
FPMO209K F 
Built-In
Microwave Specifications
Product Shipping Weight (Approx.) – 46 Lbs.
(not incl. Trim Kit)
Voltage Rating – 120V / 60 Hz / 15 or 20 Amps
Connected Load (kW Rating) @ 120 Volts = 1.7 kW
(For use on adequately wired 120V, dedicated circuit having
2-wire service with a separate ground wire. Appliance must
be grounded for safe operation.)
Amps @ 120 Volts = 14.3 Amps
Always consult local and national electric codes.
Microwave can stand alone on countertop or be built in with optional
30" or 27" Trim Kit
(ordered by individual part number)
which
includes Bottom Duct Assembly – shipped in separate box.
Allow 21" minimum clearance for 90° door swing.
Minimum 20" deep oven cutout dimension is critical for proper
installation for oven and faceplate to fit flush against cabinet front.
Consult local building code, in the event that cutout opening may be
required to be enclosed with sides, ceiling and rear partition.
Full oven base of solid plywood or similar material required, capable
of supporting 100 Lbs.
Base must be level and front of cabinet square for proper operation.
Grounded outlet should NOT be located in shaded area, as indicated,
UNLESS cabinet depth is greater than 21".
Can NOT be installed above any gas wall oven.
Built-In Microwave is approved to be used in combination with any
Frigidaire® Electric Single Wall Oven and /or Warmer Drawer.
(Refer to
model-specific Combination Installation Specification pages on web.)
When used in combination with another Frigidaire® built-in product,
a minimum clearance of 2-7/8" required from bottom of Built-In
Microwave cutout to top edge of companion product’s faceplate,
leaving a 2" visible gap between both product faceplates.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at frigidaire.com for detailed instructions
Optional Accessories
30" Stainless Steel Trim Kit – (PN # MWTK30KF).
27" Stainless Steel Trim Kit – (PN # MWTK27KF).