Frigidaire PLD4375RFC Parts Diagram - Page 2

To start Close and latch door. Press START/CANCEL pad. To delay start Close and latch door. Press DELAY START pad to select desired delay time. To select a new cycle or option Press desired cycle and/or option pad. The indicator lights will change. Press START/CANCEL within 15 seconds to begin cycle. To cancel cycle Press START/CANCEL. Dishwasher will drain for For controls 90 seconds, then shut off. lock Press and hold the RINSE ONLY or AIR DRY pad for 3 seconds. To unlock, press and hold the RINSE ONLY or AIR DRY pad for 3 seconds. Display Codes (Readout) ER/CE....Configuration Error ER/uo.....Vent will not close ER/uF.....Fan not running Display Codes (LED) SENSING Turbidity sensor is checking the condition of the wash/rinse water. No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL. WASHING Wash portion of cycle. SANITIZED The SANITIZED criteria has been met. Indicator light will switch off when door is opened. DRYING Drying portion of cycle. CLEAN Shows completion of cycle. Indicator light will switch off when door is opened. OPTION LED's Flashing -- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has occurred. Press START/CANCEL pad and reselect desired options and cycle. STATUS LED's Flashing -- The STATUS LED's that are lit when the door is opened will flash. Close door. RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is filled. (Some models) Wiring Diagram BK Black BU Blue PK Pink R Red R-BK Red/Black W White Y-BK Yellow/Black R-W Red/White BK-W Black/White R-Y Red/Yellow VIO Violet P6 DISPLAY P2- 4 ELECTRONIC P2- 5 CONTROL P2- 6 BOARD P-5 W P2-1 R P2-2 BK P2-3 BK P3-5 BK P1 W P3-6 P1 THERMOSTAT R FLOAT SWITCH PK P3- 1 R-Y P3- 3 BK P2- 7 BK P2- 8 P3-7 VIO P3-2 Y P3-8 BU P3-4 P32-9 P32-6 P2-11 P2-12 P2-13 Display flashes when Detection of failure USER INTERFACE SWITCH R W BK BK R BK-W R-W Y/BL HI-LIMIT TOTAL TIME (SEC) WATER VALVE CIRCULATION MOTOR DRAIN MOTOR HEATER DISPENSER FAN UNIT SENSING LED WASHING LED SANITIZED LED DRYING LED CLEAN LED RINSE LED Device being monitored DOOR L1 BK SWITCH NEUT W STEP W CYCLES FAN DRY UNIT 1 FILL/DISPENSER 2 FILL 3 WASH/HEAT 4 PAUSE 5 WASH/HEAT 6 WASH/HEAT/DISP. 7 DRAIN 8 DRY TOTAL 60 1 0 0 0 1 0 1 1 0 0 0 0 Fan damper Uo 27 1 0 0 0 0 0 1 1 0 0 0 0 Turbidity Tu 45 0 1 0 1 0 0 1 1 0 0 0 0 Hall sensor HS 0.4 0 0 0 1 0 0 1 1 0 0 0 1 75 0 1 0 1 0 0 0 0 0 0 0 1 60 0 1 0 1 1 0 0 0 0 0 0 1 Thermistor Th 90 0 0 1 0 0 1 0 0 0 0 0 0 Fan speed UF 90 0 0 1 X 0 1 0 0 0 1 0 0 Rinse aid RA 447 00 1 01 0 X - denotes selectable option CLEAN LED stays on until door is opened or cycle is started. ULTIMATE/MAXX NORMAL WASH CHINA/CRYSTAL ECO WASH GLASSES SPEED WASH RINSE ONLY SENSING WASHING SANITIZED DRYING CLEAN TIME IN MINUTES WASH 1 8 MIN. RINSE 1 11 MIN. RINSE 2 11 MIN. WATER VALVE FAN/DAMPER PUMP MOTOR DRAIN MOTOR HEATER DISPENSERS TURBIDITY SENSE *Note: The Sahara/Maxx Dry will extend drying time by approximately 20 min. WASH 2 32 MIN. RINSE 3 11 MIN. RINSE 4 11 MIN. RINSE 5 11 MIN. WATER HEAT DELAY PUMP MOTOR W HALL SENSOR DRAIN MOTOR W RINSE AID LEVEL SENSE DISPENSER W TURBIDITY SENSOR/ THERMISTOR 120VAC 60HZ WATER VALVE W HEATER W RINSE 6 15.5 MIN. DRY *(HOT OR COOL) 22 MIN. WATER HEAT DELAY LED OUTPUTS