Frigidaire PLEFMZ99GC Use and Care Manual - Page 35

Care & Cleaning, Adjusting Your Oven Temperature cont'd - electric oven

Page 35 highlights

Adjusting Your Oven Temperature (cont'd) 3. Press INSTRUCTIONS to accept the temperature change and the display will return to the time of day (Fig. 3). Press to reject the change if necessary. To adjust the oven temperature lower: 1. Press for 6 seconds (Fig. 4). 2. To decrease the temperature use the number pads to enter the desired change. (Example -30°F) and then press (Fig. 5). The temperature may be decreased as much as 35°F (19°C). 3. Press to accept the temperature change and the display will return to the time of day (Fig. 6). Press to reject the change if necessary. PRESS DISPLAY Fig. 3 Fig. 4 Fig. 5 Fig. 6 Care & Cleaning Changing the Oven Light The oven light bulb is located at the rear of the oven and is covered with a glass shield held by a wire holder. The glass shield must be in place whenever the oven is in use. To replace the oven light bulb: 1. Turn electrical power off at the main source or unplug the range. 2. Press wire holder to one side to release the glass shield. 3. Replace bulb with a new 40 watt appliance bulb. 4. Replace glass shield over bulb and snap wire holder into place. 5. Turn power back on again at the main source (or plug the range back in). 6. The clock will then need to be reset. To reset, see Setting the Clock and Minute Timer. Be sure the range is unplugged and all parts are COOL before replacing oven light. Wear a leather-faced glove for protection against possible broken glass. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

35
Care & Cleaning
Adjusting Your Oven Temperature (cont’d)
INSTRUCTIONS
PRESS
DISPLA
Y
The oven light bulb is located at the rear of the oven and is covered with a glass
shield held by a wire holder. The glass shield must be in place whenever the oven is
in use.
To replace the oven light bulb:
1.
Turn electrical power off at the main source or unplug the range.
2.
Press wire holder to one side to release the glass shield.
3.
Replace bulb with a new 40 watt appliance bulb.
4.
Replace glass shield over bulb and snap wire holder into place.
5.
Turn power back on again at the main source (or plug the range back in).
6.
The clock will then need to be reset. To reset, see
Setting the Clock and
Minute Timer
.
Be sure the range is unplugged and all parts are COOL before
replacing
oven light. Wear a leather-faced glove for protection against possible
broken glass.
Changing the Oven Light
3.
Press
to accept the temperature change and the display will
return to the time of day (Fig. 3). Press
to reject the change if
necessary.
To adjust the oven temperature lower:
1.
Press
for 6 seconds (Fig. 4).
2.
To decrease the temperature use the number pads to enter the
desired change.
(Example -30°F)
and then press
(Fig. 5).
The temperature may be decreased
as much as 35°F
(19°C).
3.
Press
to accept the temperature change and the display will
return to the time of day (Fig. 6). Press
to reject the change if
necessary.
Fig. 3
Fig. 4
Fig.
5
Fig.
6