Fujitsu MHV2080AH Manual/User Guide - Page 30

Spare Parts, 2.2 Disk Drive Removal, Removal and Replacement Procedure - r 80gb

Get Fujitsu MHV2080AH - 80GB UDMA/100 5400RPM 8MB Notebook Hard Drive PDF manuals and user guides
UPC - 683728128517
View all Fujitsu MHV2080AH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

Removal and Replacement Procedure 2.1 Spare Parts See Table 2.1 for the model and parts numbers to order the replacement disk drive. Table 2.1 Model and parts numbers Model Name MHV2100AH MHV2080AH MHV2060AH MHV2040AH Capacity (user area) 100GB 80GB 60GB 40GB Mounting screw M3 Depth 3 M3 Depth 3 M3 Depth 3 M3 Depth 3 Order No. CA06531-B040/B140 CA06531-B048/B148 CA06531-B036/B136 CA06531-B024/B124 2.2 Disk Drive Removal The method and procedures to demount the disk drive to check the jumper terminal, change the jumper position, or replace the device differ depend on the system cabinet structure. Therefore, for actual working procedures, the specific conditions necessary for each system must be determined. The general removal procedures, with notes, are as follows. a) Disconnect the power-interface cable. b) Remove the screws that attach the drive and remove the drive from the system cabinet. c) When storing or transporting the drive, pack it an antistatic bag in compliance with section 1.1.2 (5) d. and (5) e.. To protect the device from damage and prevent the worker getting hurt, observe the following cautions and precautions in Subsection 1.1.1. Damage or Device damage 1. Perform any removal after the system power is completely disconnected. The cable must not be disconnected and the screws that attach the drive must not be removed with the power ON. 2. Do not move the drive and attach or detach the connector until it comes to a complete stop (about 30 s after the power is turned OFF). 3. Perform the human body grounding to discharge any static electricity from your body (Be sure to wear a wrist strap). 2-2 C141-F071

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Removal and Replacement Procedure
2-2
C141-F071
2.1
Spare Parts
See Table 2.1 for the model and parts numbers to order the replacement disk
drive.
Table 2.1 Model and parts numbers
Model Name
Capacity
(user area)
Mounting screw
Order No.
MHV2100AH
100GB
M3 Depth 3
CA06531-B040/B140
MHV2080AH
80GB
M3 Depth 3
CA06531-B048/B148
MHV2060AH
60GB
M3 Depth 3
CA06531-B036/B136
MHV2040AH
40GB
M3 Depth 3
CA06531-B024/B124
2.2
Disk Drive Removal
The method and procedures to demount the disk drive to check the jumper
terminal, change the jumper position, or replace the device differ depend on the
system cabinet structure.
Therefore, for actual working procedures, the specific
conditions necessary for each system must be determined.
The general removal
procedures, with notes, are as follows.
a)
Disconnect the power-interface cable.
b)
Remove the screws that attach the drive and remove the drive from the
system cabinet.
c)
When storing or transporting the drive, pack it an antistatic bag in compliance
with section 1.1.2 (5) d. and (5) e..
To protect the device from damage and prevent the worker getting hurt, observe
the following cautions and precautions in Subsection 1.1.1.
Damage or Device damage
1.
Perform any removal after the system power is completely
disconnected.
The cable must not be disconnected and the
screws that attach the drive must not be removed with the
power ON.
2.
Do not move the drive and attach or detach the connector until
it comes to a complete stop (about 30 s after the power is
turned OFF).
3.
Perform the human body grounding to discharge any static
electricity from your body (Be sure to wear a wrist strap).