Garmin GPSMAP 421 Owner's Manual - Page 11

Using Simulator Mode, Viewing System Information, Restoring the Original Factory Settings - gps chartplotter

Get Garmin GPSMAP 421 PDF manuals and user guides View all Garmin GPSMAP 421 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

MENU-Press to access additional settings and configuration options. Press to return to the previous screen when indicated. Acquiring GPS Satellite Signals When you turn on the unit, the GPS receiver must collect satellite data and establish the current location. When the unit acquires satellite signals, the signal strength bars at the top of the Home screen are green . When the unit loses satellite signals, the green bars disappear and the position icon displays a flashing question mark. For more information about GPS, visit the Garmin Web site at www.garmin.com/aboutGPS. Using Simulator Mode Simulator mode turns the GPS receiver off for use indoors or for practice. The unit does not track satellites in simulator mode.  Warning Do not try to navigate using simulator mode, because the GPS receiver is turned off. Any satellite signal-strength bars shown are only simulations and do not represent the strength of actual satellite signals. Getting Started To turn on Simulator mode: 1. From the Home screen, select Configure > System > Simulator. 2. Select Setup to set speed, track control, and position. Viewing System Information You can view the software version, the basemap version, supplemental map information (if applicable), and the unit ID number for your chartplotter. You may need this information to update the system software or to purchase additional map data. From the home screen, select Configure > System > System Information. Restoring the Original Factory Settings NOTE: This procedure deletes all settings information you have entered. 1. From the Home screen, select Configure > System > System Information > Factory Settings. 2. Select Yes to restore all factory settings, or select No to cancel. The unit reboots and prompts you to adjust unit settings (page 2). GPSMAP 400/500 Series Owner's Manual 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
GPSMAP 400/500 Series Owner’s Manual
5
Getting Started
MENU
—Press to access additional settings and configuration
options. Press to return to the previous screen when indicated.
Acquiring GPS Satellite Signals
When you turn on the unit, the GPS receiver must collect satellite
data and establish the current location. When the unit acquires
satellite signals, the signal strength bars at the top of the Home
screen are green
. When the unit loses satellite signals, the
green bars disappear
and the position icon displays a flashing
question mark.
For more information about GPS, visit the Garmin Web site at
www.garmin.com/aboutGPS
.
Using Simulator Mode
Simulator mode turns the GPS receiver off for use indoors or for
practice. The unit does not track satellites in simulator mode.
WARNING
Do not try to navigate using simulator mode, because the GPS
receiver is turned off. Any satellite signal-strength bars shown are
only simulations and do not represent the strength of actual satellite
signals.
To turn on Simulator mode:
1. From the Home screen, select
Configure
>
System
>
Simulator
.
2. Select
Setup
to set speed, track control, and position.
Viewing System Information
You can view the software version, the basemap version,
supplemental map information (if applicable), and the unit ID
number for your chartplotter. You may need this information to
update the system software or to purchase additional map data.
From the home screen, select
Configure
>
System
>
System
Information
.
Restoring the Original Factory Settings
NOTE
: This procedure deletes all settings information you have
entered.
1. From the Home screen, select
Configure
>
System
>
System
Information
>
Factory Settings
.
2. Select
Yes
to restore all factory settings, or select
No
to cancel.
The unit reboots and prompts you to adjust unit settings (
page 2
).