Garmin GT8HW-TM Plastic Transom or Trolling Motor Mount Transducer High Wide CHI

Garmin GT8HW-TM Plastic Transom or Trolling Motor Mount Transducer High Wide CHIRP 150-240 kHz 250W 8-pin Manual

Get Garmin GT8HW-TM Plastic Transom or Trolling Motor Mount Transducer High Wide CHIRP 150-240 kHz 250W 8-pin PDF manuals and user guides View all Garmin GT8HW-TM Plastic Transom or Trolling Motor Mount Transducer High Wide CHIRP 150-240 kHz 250W 8-pin manuals
Add to My Manuals
Save this manual to your list of manuals

Garmin GT8HW-TM Plastic Transom or Trolling Motor Mount Transducer High Wide CHIRP 150-240 kHz 250W 8-pin manual content summary:

  • 1
  • 2
  • 3
  • 4
GT8HW-TM Transducer
Installation Instructions
Important Safety Information
WARNING
See the
Important Safety and Product Information
guide in the
chartplotter or fishfinder product box for product warnings and
other important information.
You are responsible for the safe and prudent operation of your
vessel. Sonar is a tool that enhances your awareness of the
water beneath your boat. It does not relieve you of the
responsibility of observing the water around your boat as you
navigate.
CAUTION
Failure to install and maintain this equipment in accordance with
these instructions could result in damage or injury.
Always wear safety goggles, ear protection, and a dust mask
when drilling, cutting, or sanding.
NOTICE
When drilling or cutting, always check what is on the opposite
side of the surface.
To obtain the best performance and to avoid damage to your
boat, you must install the Garmin
®
transducer according to these
instructions.
Read all installation instructions before proceeding with the
installation. If you experience difficulty during the installation,
contact Garmin Product Support.
Tools Needed
•
Drills and drill bits
•
Number 2 Phillips screwdriver
•
Masking tape
•
Marine sealant
Preparing the Transducer for Long-Term Exposure to
Water
NOTICE
Do not use acetone or acetone-based products on the
transducer. Acetone damages the plastic transducer housing.
When you install a transducer on a boat that spends a
significant amount of time in the water, you should coat the
transducer and mounting hardware with a water-based anti-
fouling paint to prevent marine growth.
1
Lightly sand the transducer and mounting hardware with a
fine-grit abrasive pad.
2
Wipe the transducer and mounting hardware with isopropyl
alcohol.
3
Apply water-based anti-fouling paint to the transducer and
mounting hardware.
Mounting Consideration
To ensure peak performance with the lowest noise and
interference, you should route the transducer cable away from
ignition wires, house batteries and wires, trolling motor batteries
and wires, and high-energy wires such as radar, audio amplifier,
and autopilot pump wires.
Assembling the Transducer
Attach the transducer
À
to the mount with the included lock
nut
Á
, rubber washer
Â
, metal washer
Ã
, and bolt
Ä
.
NOTE:
The bolt should be tight enough to hold the
transducer in place when the boat moves at high speed, but
loose enough to allow the transducer to pivot out of the way if
the transducer hits an obstruction.
Installing the Transducer on a Transom
Mounting Location Considerations
•
The transducer should be mounted as close to the center of
the boat as possible.
•
The transducer should not be mounted behind strakes, struts,
fittings, water intake or discharge ports, or anything that
creates air bubbles or causes the water to become turbulent.
The transducer must be in clean (non-turbulent) water for
optimal performance.
•
The transducer should not be mounted in a location where it
might be jarred when launching, hauling, or storing.
•
On single-drive boats, the transducer must not be mounted in
the path of the propeller.
The transducer can cause cavitation that can degrade the
performance of the boat and damage the propeller.
•
On twin-drive boats, the transducer should be mounted
between the drives, if possible.
Installing the Transom-Mount Hardware
NOTICE
If you are mounting the bracket on fiberglass with screws, it is
recommended to use a countersink bit to drill a clearance
counterbore through only the top gel-coat layer. This will help to
avoid any cracking in the gel-coat layer when the screws are
tightened.
The cables connected to the transducer should not be cut,
because cutting the transducer cables voids your warranty.
1
Position the transducer mount
À
so the center of the bottom
of the transducer is level with the bottom edge of the transom
and is parallel to the water line.
December 2015
Printed in Taiwan
190-01974-02_0A