Garmin GTM 10 Installation Sheet - Page 4

Step 5: Test the GTM 10, Activating a Subscription, Verify that you are in a service area - receiver

Get Garmin GTM 10 - TMC Module PDF manuals and user guides
UPC - 753759050320
View all Garmin GTM 10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

• Verify Signal Strength: If you are inside a building where radio signals cannot be received, you may need to take the vehicle outside for testing. • Verify that you are in a service area: Check for service from the pay service or free services, if available. • Check the Map: Turn on the GPS device and access a map. Check for traffic alerts and symbols on the map. It may be easiest to browse the map of a roadway or intersection under construction or that is known to have frequent traffic hazards. If possible, refer to the Owner's Manual. If the above tests fail, either you are not in a service area, the purchased subscription is not activated (see below), or the installation might be faulty. Activating a Subscription If the owner has marked Yes for 2b, you need to enter the 25-character code into the GPS device to activate the purchased subscription. As each GPS device operates differently, consult the Owner's Manual for complete information about entering the code. After you enter the code to activate the subscription, you can use the steps listed above to test the installation. step 6: Mount the GTM 10 If possible, place the GTM 10 where the LED can be seen without dismantling the dashboard. 1. Mount the GTM 10 according to the owner's response to question 3: • Attach with foam tape: clean and dry a flat surface behind the dashboard. Remove the backing from the foam tape and attach the GTM 10 to the flat surface. • Hang freely: bind up any slack cable from the mini-USB cable with a wire tie and let the GTM 10 hang freely behind the radio. 2. Check that all cables and the GTM 10 are secure and free of obstruction. 3. Replace all parts of the dashboard to their original locations. 4. Repeat the testing as described in Step 5. Garmin International, Inc. 1200 East 151st Street, Olathe, Kansas 66062 U.S.A. Tel. 913/397.8200 Fax. 913/397.8282 August 2005 © Copyright 2005 Garmin Ltd. or its subsidiaries Garmin (Europe) Ltd. Unit 5, The Quadrangle, Abbey Park Industrial Estate, Romsey, SO51 9DL U.K. Tel. 44/0870.8501241 Fax. 44/0870.8501251 Part Number 190-00478-01 Rev. B Garmin Corporation No. 68, Jangshu 2nd Road, Shijr, Taipei County, Taiwan Tel. 886/2.2642.9199 Fax. 886/2.2642.9099 Printed in Taiwan

  • 1
  • 2
  • 3
  • 4
• Verify Signal Strength:
If you are inside a building where radio signals cannot be received, you may need
to take the vehicle outside for testing.
•
Verify that you are in a service area:
Check for service from the pay service or free services, if available.
• Check the Map:
Turn on the GPS device and access a map. Check for traffic alerts and symbols on the
map. It may be easiest to browse the map of a roadway or intersection under construction or that is known
to have frequent traffic hazards. If possible, refer to the
Owner’s Manual
.
If the above tests fail, either you are not in a service area, the purchased subscription is not activated (see
below), or the installation might be faulty.
Activating a Subscription
If the owner has marked
Yes
for 2b, you need to enter the 25-character code into the GPS device to activate
the purchased subscription. As each GPS device operates differently, consult the
Owner’s Manual
for
complete information about entering the code. After you enter the code to activate the subscription, you can
use the steps listed above to test the installation.
Step 6: Mount the GTM 10
If possible, place the GTM 10 where the LED can be seen without dismantling the dashboard.
1. Mount the GTM 10 according to the owner’s response to question 3:
•
Attach with foam tape: clean and dry a flat surface behind the dashboard. Remove the backing from
the foam tape and attach the GTM 10 to the flat surface.
•
Hang freely: bind up any slack cable from the mini-USB cable with a wire tie and let the GTM 10 hang
freely behind the radio.
2. Check that all cables and the GTM 10 are secure and free of obstruction.
3. Replace all parts of the dashboard to their original locations.
4. Repeat the testing as described in Step 5.
© Copyright 2005 Garmin Ltd. or its subsidiaries
Garmin International, Inc.
1200 East 151st Street,
Olathe, Kansas 66062 U.S.A.
Tel. 913/397.8200
Fax. 913/397.8282
Garmin (Europe) Ltd.
Unit 5, The Quadrangle,
Abbey Park Industrial Estate,
Romsey, SO51 9DL U.K.
Tel. 44/0870.8501241
Fax. 44/0870.8501251
Garmin Corporation
No. 68, Jangshu 2nd Road,
Shijr, Taipei County, Taiwan
Tel. 886/2.2642.9199
Fax. 886/2.2642.9099
August 2005
Part Number 190-00478-01 Rev. B
Printed in Taiwan