Garmin VIRB Elite for Aviation Bundle Owners Manual - Page 6

Mounting the Device, Turning On the Device

Get Garmin VIRB Elite for Aviation Bundle PDF manuals and user guides View all Garmin VIRB Elite for Aviation Bundle manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

Keys Select to scroll through menus and settings. Select to scroll through menus and settings. OK Select to choose menu options or to take a photo. MODE REC Select to scroll through modes. Hold to turn the device on and off. Slide toward the lens to record video. Mounting the Device NOTICE To prevent product loss or damage, do not use the adhesive mounting base when the temperature is below 5°F (-15°C). The permanent mounting adhesive is extremely difficult to remove after it is installed. Before you can install the adhesive mounting base onto a surface, the ambient temperature must be from 70° to 100°F (from 21° to 38°C). Your device includes an assortment of mounting bases and arms, which can be used in many configurations. These instructions provide an example of one possible configuration. You can also purchase additional mounts for your device, such as wearable mounts, vehicle mounts, or a tripod mount. Go to www.garmin.com/ outdoor for more information. NOTE: By default, the camera should be mounted with the screen facing up to record correctly oriented video. You can adjust the settings to record with the screen facing down (Advanced Recording Settings). 1 Thoroughly clean the mounting surface using water or alcohol. The mounting surface must be free of dirt, debris, wax, or coatings. 2 Remove the film from the adhesive mounting base À, and press the base firmly onto the mounting surface. You can use either the flat base or the curved base, depending on the contour of the mounting surface. 3 Allow the base to bond to the mounting surface for at least 24 hours. 4 Place the coupler Á into the base. 5 Place the threaded ring  over the coupler, and tighten it onto the base. 6 Snap the mounting arm à into the coupler. 7 Insert a thumbscrew Ä into the larger opening of the joint, and tighten the thumbscrew to lock the angle of the joint. 8 Snap the camera mount Å into the top of the mounting arm. 9 Insert a thumbscrew into the larger opening of the joint, and tighten the thumbscrew to lock the angle of the joint. 10Place the tab Æ on the back of the camera mount into the slot in the back of the camera. 11Squeeze the buttons Ç on the sides of the mount, press the front of the camera È down, and release the buttons. The camera should be held tightly and should not move in the mount when properly secured. 12If the camera feels loose in the mount, press the front of the camera into the mount until it clicks. Turning On the Device Select . Turning Off the Device NOTICE To prevent loss of data, always turn off the device before removing the battery. NOTE: You cannot turn off the device while recording video. 1 If necessary, slide REC away from the lens. 2 Hold . appears on the screen while the device saves track log data and turns off. 2 Introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
Keys
Select to scroll through menus and settings.
Select to scroll through menus and settings.
OK
Select to choose menu options or to take a photo.
MODE
Select to scroll through modes.
Hold to turn the device on and off.
REC
Slide toward the lens to record video.
Mounting the Device
NOTICE
To prevent product loss or damage, do not use the adhesive
mounting base when the temperature is below 5°F (-15°C).
The permanent mounting adhesive is extremely difficult to
remove after it is installed.
Before you can install the adhesive mounting base onto a
surface, the ambient temperature must be from 70° to 100°F
(from 21° to 38°C).
Your device includes an assortment of mounting bases and
arms, which can be used in many configurations. These
instructions provide an example of one possible configuration.
You can also purchase additional mounts for your device, such
as wearable mounts, vehicle mounts, or a tripod mount. Go to
www.garmin.com/outdoor
for more information.
NOTE:
By default, the camera should be mounted with the
screen facing up to record correctly oriented video. You can
adjust the settings to record with the screen facing down
(
Advanced Recording Settings
).
1
Thoroughly clean the mounting surface using water or
alcohol.
The mounting surface must be free of dirt, debris, wax, or
coatings.
2
Remove the film from the adhesive mounting base
À
, and
press the base firmly onto the mounting surface.
You can use either the flat base or the curved base,
depending on the contour of the mounting surface.
3
Allow the base to bond to the mounting surface for at least
24 hours.
4
Place the coupler
Á
into the base.
5
Place the threaded ring
Â
over the coupler, and tighten it
onto the base.
6
Snap the mounting arm
Ã
into the coupler.
7
Insert a thumbscrew
Ä
into the larger opening of the joint,
and tighten the thumbscrew to lock the angle of the joint.
8
Snap the camera mount
Å
into the top of the mounting arm.
9
Insert a thumbscrew into the larger opening of the joint, and
tighten the thumbscrew to lock the angle of the joint.
10
Place the tab
Æ
on the back of the camera mount into the
slot in the back of the camera.
11
Squeeze the buttons
Ç
on the sides of the mount, press the
front of the camera
È
down, and release the buttons.
The camera should be held tightly and should not move in
the mount when properly secured.
12
If the camera feels loose in the mount, press the front of the
camera into the mount until it clicks.
Turning On the Device
Select
.
Turning Off the Device
NOTICE
To prevent loss of data, always turn off the device before
removing the battery.
NOTE:
You cannot turn off the device while recording video.
1
If necessary, slide
REC
away from the lens.
2
Hold
.
appears on the screen while the device saves track log data
and turns off.
2
Introduction