Gastroback 40128 User Manual - Page 8

Assembling the appliance

Get Gastroback 40128 PDF manuals and user guides View all Gastroback 40128 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Assembling the appliance Step1: A Place the filter bowl surround on the motorblock. Locate the filter bowl surround so that the spout fits through the hole on the front of the motor base (picture A). Step2: WARNING: Handle the units with care and do not use any force. Pay attention to the sharp blades on the stainless steel micro mesh filter and the feed chute to avoid injury. Always completely assemble your juicer before you plug the plug into the power point. ATTENTION: Ensure the stainless steel filter basket is clean B before assembling. Any dehumidified left over food on the basket will block the fine mesh holes. If necessary remove excess fibre build up (from fruit or vegetables) according to the instructions ´Care and Cleaning`. Align the arrows on the stainless steel filter basket with the arrows on the motor drive coupling and push down until it clicks into place. Ensure the stainless steel filter basket is fitted securely inside the integrated pulp container and onto the motor base (picture B). Step 3: C Place the juicer cover over the stainless steel filter on top of the filter bowl surround (picture C). The feed chute has to be positioned in the middle of the filter basket and the pulp spouting of the cover has to face away from the interlocking safety arm. Step 4: Raise the safety locking arm straight up and lock into the two grooves on either side of the juicer cover. The safety locking arm should now be in a vertical position and locked into place on top of the juicer cover (picture D). D Important: If the safety locking arm is not in the right position the motor will not start moving and the display shows "Lockbar". Step 5: Slide the food pusher down the feed chute by aligning the groove of the food pusher with the small protrusion on the inside of the top of the feed chute. Continue to slide the food pusher down the feed chute (picture E) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Assembling the appliance
Step1:
Place the filter bowl surround on the motorblock. Locate the
filter bowl surround so that the spout fits through the hole on
the front of the motor base (picture A).
Step2:
WARNING:
Handle the units with care and
do not
use any
force. Pay attention to the sharp blades on the stainless steel
micro mesh filter and the feed chute to avoid injury. Always
completely assemble your juicer before you plug the plug into
the power point.
ATTENTION:
Ensure the stainless steel filter basket is clean
before assembling. Any dehumidified left over food on the
basket will block the fine mesh holes. If necessary remove
excess fibre build up (from fruit or vegetables) according to
the instructions ´Care and Cleaning`.
Align the arrows on the stainless steel filter basket with the
arrows on the motor drive coupling and push down until it
clicks into place. Ensure the stainless steel filter basket is fitted
securely inside the integrated pulp container and onto the
motor base (picture B).
Step 3:
Place the juicer cover over the stainless steel filter on top of
the filter bowl surround (picture C). The feed chute has to be
positioned in the middle of the filter basket and the pulp
spouting of the cover has to face away from the interlocking
safety arm.
Step 4:
Raise the safety locking arm straight up and lock into the two
grooves on either side of the juicer cover. The safety locking
arm should now be in a vertical position and locked into place
on top of the juicer cover (picture D).
Important:
If the safety locking arm is not in the right position
the motor will not start moving and the display shows “Lockbar”.
Step 5:
Slide the food pusher down the feed chute by aligning the
groove of the food pusher with the small protrusion on the
inside of the top of the feed chute. Continue to slide the
food pusher down the feed chute (picture E)
8
A
B
C
D