GE AEM12AP Owners Manual - Page 5

Fan Only Mode

Get GE AEM12AP PDF manuals and user guides View all GE AEM12AP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

GEAppliances.com Cool Mode Use the Cool mode at Low, Meal,High or Auto Fen Speed for cooling. Use the Temperature Increase • / Decrease • pads to set the desired temperature between 64°Fand 86°Fin l°F increments. An electronic thermostat is used to maintain the room temperature. The compressor will cycle on and off to keepthe room at the set level of comfort. Set the thermostat at a lower number and the indoor air will become cooler. Setthe thermostat at a higher number and the indoor air will become warmer. NOTE:If the air conditioner is off and is then turned on while set to a Cool setting or if turned from a fan setting to a Cool setting, it may take approximately 3 minutes for the compressor to start and cooling to begin. Cooling Descriptions For Normal Cooling-Select the Cool mode and High or Med fan with a middle set temperature. For Maximum Cooling-Select the Cool mode and High fan with a lower set temperature. For Quieter and Nighttime Cooling-Select the Cool mode and Low fan with a middle set temperature. Energy Saver Mode Controls the fan. ON--The fan will cycle on and off with the compressor. This results in wider variations of room temperature and humidity. Normally used when the room is unoccupied. NOTE:Thefan may continue to run for a short time after the compressor cyclesoff. OFF--Thefun runs oil the time, while the compressor cycles on and off. Fan Only Mode Use the FanOnly Mode at Low, Med or High fan speed to provide air circulation and filtering without cooling. Since fan-only settings do not provide cooling, a Settemperature cannot be entered. The room temperature will appear in the display. NOTE:Auto Fan Speed cannot be used when in the Fan Only Mode. Auto Fan Speed Set to Auto fun speed for the fun speed to automatically set to the speed needed to provide optimum comfort settings with the set temperature. If the room needs more cooling, the fun speed will automatically increase. If the room needs less cooling, the fun speed will automatically decrease. NOTE:Auto Fan Speed cannot be used when in the Fan Only Mode. Remote Control To ensure proper operation, aim the remote control at the signal receiver on the air conditioner. Hoke sure nothing is between the air conditioner and the remote control that could block the signal. The remote control signal has o range of up to 20 feet. Make sure batteries ore fresh and installed correctly as indicated on the remote control. Remote contains o magnet allowing it to attach to metal surfaces. Power Outage Recovery Feature In the case of o power outage or interruption, the unit will automatically re-start in the settings lost used offer the power is restored. If the Delay 1-24hr feature was set, it will resume countdown. You may need to set o new time if desired.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
GEAppliances.com
Cool
Mode
Use the Cool mode at
Low, Meal,High
or
Auto Fen
Speed
for cooling. Use the
Temperature Increase
•
/ Decrease
•
pads to set the desired temperature
between 64°Fand 86°Fin l°F increments.
An electronic thermostat is used to maintain the room
temperature. The compressor will cycle on
and off to keepthe room at the set level of comfort.
Set the thermostat at a lower number and the indoor
air will become cooler. Setthe thermostat at a higher
number and the indoor air will become warmer.
NOTE:If the air conditioner is off and is then turned on
while set to a
Cool
setting or if turned from a fan
setting
to a
Cool setting,
it
may
take approximately
3
minutes for the
compressor
to
start
and
cooling
to
begin.
Cooling
Descriptions
For Normal
Cooling-Select the Cool mode and
High
or
Med
fan with a middle set temperature.
For
Maximum Cooling-Select the Cool mode
and
High
fan with a lower set temperature.
For Quieter
and
Nighttime
Cooling-Select the
Cool mode and
Low
fan with a middle set
temperature.
Energy
Saver
Mode
Controls the fan.
ON--The
fan will cycle on and off with the
compressor. This results in wider variations of room
temperature and humidity. Normally used when the
room is unoccupied.
NOTE:Thefan may
continue
to
run for a short time after the compressor cyclesoff.
OFF--The
fun runs oil the time, while the compressor
cycleson and off.
Fan Only Mode
Use the FanOnly Mode at Low, Med or High fan
speed to provide air circulation and filtering without
cooling. Since fan-only settings do not provide
cooling, a Settemperature cannot be entered. The
room temperature will appear
in the display.
NOTE:Auto Fan Speed
cannot
be used when
in the
Fan Only Mode.
Auto
Fan Speed
Set to Auto fun speed for the fun speed to
automatically set to the speed needed to provide
optimum comfort settings with the set temperature.
If the room needs more cooling, the fun speed
will automatically increase. If the room needs less
cooling, the fun speed will automatically decrease.
NOTE:Auto Fan Speed
cannot
be used when in the
Fan Only Mode.
Remote
Control
To ensure proper operation, aim the remote
control at the signal receiver on the air
conditioner.
Hoke
sure nothing is between the air conditioner
and the remote control that could block the
signal.
The remote control signal has o range of
up to 20 feet.
Make sure batteries ore fresh and installed
correctly as indicated on the remote control.
Remote contains o magnet allowing it to attach
to metal surfaces.
Power
Outage
Recovery
Feature
In the case of o power outage or interruption, the
unit will automatically re-start in the settings lost
used offer the power is restored. If the Delay 1-24hr
feature was set, it will resume countdown. You may
need to set o new time if desired.