GE AJCQ12DCD Use and Care Manual - Page 17

Remove Air Conditioner From Case, Storm Window Requirements, Wood Pieces, Width, Length, Thickness

Get GE AJCQ12DCD PDF manuals and user guides
UPC - 084691175377
View all GE AJCQ12DCD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installation Instructions 2 STORM WINDOW REQUIREMENTS A storm window frame will not allow the air conditioner to tilt towards the outside and will keep it from draining properly. To adjust for this, attach a piece of wood to the stool. Wood 1/2″ higher than frame Stool Sill Storm window frame WOOD PIECES WIDTH: 2″ LENGTH: Long enough to fit inside the window frame. THICKNESS: To determine the thickness, place a piece of wood on the stool to make it 1/2″ higher than the top of the storm window frame. Attach securely with nails or screws provided by the installer. 3 REMOVE AIR CONDITIONER FROM CASE A Remove the front grille. See the Care and Cleaning section. B Find the locking plate located on the front left side. C Remove the screw and the locking plate to unlock the air conditioner. F Remove all shipping pads (if present) inside the air conditioner next to the compressor. Locking plate Remove screw Remove shipping pads (if present) D Remove and discard the shipping screw on the back of the air conditioner to allow removal of the air conditioner from the case. G Remove the rear grille that is taped to the back of the case. Remove the packet of screws taped to the back of the grille. While holding the grille at a 45° angle, insert it into the clips at the top of the case and push the bottom in. Keep slight upward pressure on the grille until it fits flush with the bottom of the case. If attaching the grille If attaching the grille from the outside of the from the inside of the case, case, use the 2 long screws. use the 2 short screws. Clips Remove screw E Pull the bottom corners of the air conditioner and slide it out of the case. Insert the 2 long screws on the outside 17 Insert the 2 short screws on the inside

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
REMOVE AIR CONDITIONER FROM CASE
Remove the front grille. See the Care and Cleaning
section.
Find the locking plate located on the front
left side.
Remove the screw and the locking plate to unlock
the air conditioner.
Remove and discard the shipping screw
on the back of the air conditioner to allow removal
of the air conditioner from the case.
Pull the bottom corners of the air conditioner
and slide it out of the case.
Remove all shipping pads (if present) inside the air
conditioner next to the compressor.
Remove the rear grille that is taped to the back
of the case. Remove the packet of screws taped
to the back of the grille. While holding the grille at a
45° angle, insert it into the clips at the top of the case
and push the bottom in. Keep slight upward pressure
on the grille until it fits flush with the bottom of the
case.
17
STORM WINDOW REQUIREMENTS
A storm window frame will not allow the air
conditioner to tilt towards the outside and will keep
it from draining properly. To adjust for this, attach
a piece of wood to the stool.
WOOD PIECES
WIDTH:
2
″
LENGTH:
Long enough to fit inside the window frame.
THICKNESS:
To determine the thickness, place a piece
of wood on the stool to make it 1/2
″
higher than the top
of the storm window frame.
Attach securely with nails or screws provided by
the installer.
2
1/2
″
higher
than frame
Storm
window
frame
Wood
Stool
Sill
3
A
B
C
Locking
plate
Remove
screw
D
Remove
screw
E
F
If attaching the grille
from the outside of the
case, use the 2 long screws.
If attaching the grille
from the inside of the case,
use the 2 short screws.
G
Clips
Insert the 2 long screws
on the outside
Insert the 2 short screws
on the inside
Installation Instructions
Remove shipping pads
(if present)