GE AJCS12DCB Owners Manual - Page 17

Afrome

Get GE AJCS12DCB PDF manuals and user guides View all GE AJCS12DCB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installation Instructions []STORM WINDOW REQUIREMENTS A storm window frame will not allow the air conditioner to tilt towards the outside and will keep it from draining properly. To adjust for this, attach a piece of wood to the stool. 1/2"higher _ than A frome Storm" I] window /I frame /_ ,_/- Wood II II I[ WOOD PIECES: WIDTH: 2" LENGTH: Long enough to fit inside the window frame. THICKNESS: To determine the thickness, place a piece of wood on the stool to make it 1/2" higher than the top of the storm window frame. Attach securely with nails or screws provided by the installer. r_REMOVE AIR CONDITIONER FROM CASE [] Remove the three shipping pads inside the air [] Remove the front grille. See the Care and conditioner next to the compressor. Cleaning section, [] Find the locking plate located on the front left side, [] Remove the screw and the locking plate to unlock the air conditioner. Locking plate screw [] Remove and discard the shipping screw on the back of the air conditioner to allow removal of the air conditioner from the case. Remove screw [] Pull the bottom corners of the air conditioner and slide it out of the case. Remove shipping pads [] Remove the rear grille that is taped to the back of the case. Remove the packet of screws taped to the back of the grille. While holding the grille at a 45 ° angle, insert it into the clips at the top of the case and push the bottom in. Keep slight upward pressure on the grille until it fits flush with the bottom of the case. If attaching the grille from the outside of the case use the 2 long screws. If attaching the grille on the inside of the case use the 2 short screws. Clips I 11111111111111111I,11111111 lllllllllllllllllllllllllllllJlllllllllllllll /1111111111111111H11111111 Insert the 2 long screws on the outside Insert the 2 short screws on the inside 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
Installation
Instructions
[]STORM
WINDOW
REQUIREMENTS
A storm
window
frame
will
not allow
the air
conditioner
to tilt
towards
the outside
and will
keep
it from
draining
properly.
To adjust
for this,
attach
a piece
of wood
to the stool.
1/2"higher
_
,_/-
Wood
than
A
frome
Storm"
I]
II
window
/I
II
frame
/_
I[
WOOD
PIECES:
WIDTH:
2"
LENGTH:
Long
enough
to fit inside
the window
frame.
THICKNESS:
To determine
the thickness,
place
a
piece
of wood
on the
stool
to
make
it 1/2" higher
than
the top
of the storm
window
frame.
Attach
securely
with
nails
or screws
provided
by
the
installer.
r_REMOVE
AIR
CONDITIONER
FROM
CASE
[]
Remove
the front
grille.
See the Care and
Cleaning
section,
[]
Find
the locking
plate
located
on the front
left side,
[]
Remove
the screw
and the
locking
plate
to
Locking
plate
screw
unlock
the air conditioner.
[]
Remove
and
discard
the shipping
screw
on the
back of the
air conditioner
to
allow
removal
of the air conditioner
from
the
case.
[]
Remove
screw
Pull the bottom
corners
of the
air
conditioner
and
slide
it out of the case.
[]
Remove
the three
shipping
pads
inside
the
air
conditioner
next
to the compressor.
Remove
shipping
pads
[]
Remove
the
rear grille
that
is taped
to the back
of the case. Remove
the
packet
of screws
taped
to the
back of the grille.
While
holding
the grille
at a 45° angle,
insert
it into
the clips
at the top of
the case and
push the
bottom
in. Keep
slight
upward
pressure
on the grille
until
it fits
flush
with
the
bottom
of the case.
If attaching
the grille
from
the
outside
of
the case use the 2
long
screws.
If attaching
the grille
on the
inside
of the
case use the 2 short
screws.
Clips
Insert
the
2
long
screws
on
the
outside
I
1111111111111111111111111
I,
llllllllllllllllllllllllllllllllllllllllllll
Jl
/111111111111111111111111
H
Insert
the
2 short
screws
on the inside
17