GE CT9800SHSS Installation Instructions - Page 1
GE CT9800SHSS Manual
View all GE CT9800SHSS manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Installation Instructions 27" & 30" Electric Built-In Wall Ovens Questions? Call 1.800.GE.CARES (1.800.432.2737) or visit www.GEAppliances.com In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca BEFORE YOU BEGIN Read these instructions completely and carefully. • ,03257$17³ Save these instructions for local inspector's use. • ,03257$17³ Observe all governing codes and ordinances. • Note to Installer - Be sure to leave these instructions with Consumer. • Note to Consumer - Keep these instructions for future reference. • Skill level - Installation of this appliance requires a qualified installer or electrician. • Proper installation is the responsibility of the installer. • Product failure due to improper installation is not covered under Warranty. • Product is for indoor use only. ATTENTION INSTALLER: All electric wall ovens must be hard-wired (direct-wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. FOR YOUR SAFETY: WARNING: Before beginning the installation, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel. Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door. Make sure the wall coverings, counters and cabinets around the oven can withstand the heat (up to 200°F [93.3°C]) generated by the oven. MATERIALS YOU MAY NEED Junction Box Wire Nuts Strain Relief Clamp for 1/2" Conduit 36" (91 cm) of String TOOLS YOU MAY NEED 1/8" Drill Bit and Electric or Hand Drill Phillips Screwdriver Wire Strippers 7/16" Nut Driver T20 Screwdriver (hinge bracket) 1/4" Nut Driver DESIGN INFORMATION SINGLE OVEN INSTALLATIONS The single oven may be installed in a cabinet alone or above a warming drawer. The single oven may also be installed below a countertop or below specified cooktops. See the label on top of the oven for approved models. DOUBLE OVEN INSTALLATIONS A double oven may be installed in a cabinet alone or above a warming drawer. See the label on top of the oven for approved models. IMPORTANT: Always refer to individual installation instructions packed with each product for specific requirements. 2 PREPARE THE OPENING NOTE: If the cabinet does not have a solid bottom, two braces or runners must be installed to support the weight of the oven. For single ovens, the runners and braces must support 200 lbs (91 kg). For double ovens, the runners and braces must support 375 lbs. (170 kg). NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered. NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick, shim both sides equally to establish the cutout width. 2" x 4" (5 cm x 10 cm) or Equivalent Runners Level with Bottom of Cutout and Flush with Sides of Cutout CL Suitable Bracing to Support 1 REMOVE PACKAGING MATERIALS Failure to remove packaging materials could result in damage to the appliance. Remove all packing parts from oven, racks and heating elements. Remove protective film and labels on the outer door and control panel. Also, remove plastic on trims and panel, all tape around the oven and any shipping screws securing the oven to the base pad. Open oven door and remove literature pack and oven racks. Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process. The trim is wrapped separately and taped to the top of the unit. Remove pedestal rails from seperate box and set aside (30" Double Wall Ovens Only). 2 A CUTOUT FOR SINGLE OVENS IN WALL CABINET NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick, shim both sides equally to establish the cutout width. H These ovens are not approved for stackable installations. Junction Box Location B (junction box may be located in adjacent cabinet) Opening Between Inside Walls Must be at Least 28-1/2" (72.4 cm) Wide D 22" (55.9 cm) Min. to Bottom of Junction Box F C G E Side-by-Side Installations Install two ovens in separate cutouts. Center Line Center Line 30.5" (77.5 cm) 30" models 27" (68.58 cm) 27" models Cutout - observe all dimensions and requirements. Cutout - observe all dimensions and requirements. 2" (5.1 cm) Min. Dimension A B C D E F G H Dimension Description Cabinet Width Cutout Width Cutout Height Overlap of Oven Over Side Edges of Cutout Clearance to Adjacent Corners, Drawers, Walls, etc., When Door Is Open Overlap of Oven Top of Cutout Overlap of Oven Bottom of Cutout Junction Box Location Cutout Depth 23-1/2" (59.7 cm) Min. Note: Allow 1/4" (0.64 cm) clearances from side edges of oven door. 27" Single Oven 27" (68.6 cm) 25" (63.5 cm) min. 251ø4" (64.1 cm) max. 275ø8" (70.2 cm) min. 281ø8" (71.4 cm) max. 1" (2.5 cm) 23" (58.4 cm) min. 1" (2.5 cm) min. 1" (2.5 cm) min. 83ø4" (22.2 cm) max. right side only Recommended Cutout Location from Floor 32-1/2" (82.6 cm) A 30" Single Oven 30" (76.2 cm) 281ø2" (72.4 cm) min. 285ø8" (72.7 cm) max. 271ø4" (69.2 cm) min. 275ø16" (69.4 cm) max. 11ø16" (1.75 cm) 23" (58.4 cm) min. 1" (2.5 cm) min. (11ø4" (3.2 cm) for PT9050) 11ø4" (3.2 cm) 91ø2" (24.1 cm) max. right side only 2 B CUTOUT FOR SINGLE OVENS - UNDER COUNTER NOTE: These ovens are only approved to be installed under the specific models as labeled on the unit. Side-by-Side Installations Install two ovens in separate cutouts. Center Line Center Line 30.5" (77.5 cm) 30" models 27" (68.58 cm) 27" models Cooktop Cutout - observe all dimensions and requirements. Cutout - observe all dimensions and requirements. 2" (5.1 cm) Min. NOTE: One cooktop may be centered over either oven in the side-by-side installation. Dimension A B C Dimension Description Cabinet Width Cutout Height Unit Overlap Top 27" Single Oven 25" (63.5 cm) min. 251ø4" (64.1 cm) max. 275ø8" (70.2 cm) min. 281ø8" (71.4 cm) max. 1" (2.5 cm) D Unit Overlap Bottom E Unit Overlap Side Edges F Junction Box Location Continue to Section 4. 1" (2.5 cm) 1" (2.5 cm) 83ø4" (22.2 cm) max. right side only 30" Single Oven 281ø2" (72.4 cm) min. 285ø8" (72.7 cm) max. 271ø4" (69.2 cm) min. 275ø16" (69.4 cm) max. 1" (2.5 cm) (11ø4" (3.2 cm) for PT9050) 11ø4" (3.2 cm) 11ø16" (1.75 cm) 91ø2" (24.1 cm) max. right side only 2 C CUTOUT FOR DOUBLE OVENS (2 THERMAL OVENS) NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick, shim both sides equally to establish the cutout Hwidth. Junction B Box Location (junction box may be located in adjacent cabinet) F D C J G E Cutout Depth 23-1/2" K (59.7 cm) Min. A Dim. Description 27" Double Oven 30" Double Oven with Pedestal 30" Double Oven without Pedestal A Cabinet Width 27" (68.6 cm) 30" (76.2 cm) 30" (76.2 cm) B Cutout Width 25" (63.5 cm) min. 281ø2" (72.4 cm) min. 281ø2" (72.4 cm) min. 251ø4" (64.1 cm) max. 285ø8" (72.7 cm) max. 285ø8" (72.7 cm) max. C Cutout Height 4911ø16" (126.2 cm) min. 5113ø16" (131.6 cm) min. 50 ¼" (127.64cm) 501ø8" (127.3 cm) max. 5115ø16" (131.9 cm) max. D Overlap of Oven Over Side Edges of Cutout 1" (2.5 cm) 11ø16" (1.75 cm) 11ø16" (1.75 cm) E Clearance to 23" (58.4 cm) min. Adjacent Corners, Drawers, Walls, etc., When Door Is Open 23" (58.4 cm) min. 23" (58.4 cm) min. F Overlap of Oven Top of Cutout 1" (2.5 cm) min. 1" (2.5 cm) min. 1" (2.5 cm) min. (11ø4" (3.2 cm) for PT9550) (11ø4" (3.2 cm) for PT9550) G Overlap of Oven Bottom of Cutout 1" (2.5 cm) min. 11ø4" (3.2 cm) 11ø4" (3.2 cm) H Junction Box 83ø4" (22.2 cm) max. 91ø2" (24.1 cm) max. 91ø2" (24.1 cm) max. Location right side only right side only right side only J Height to Bottom of Junction Box 44" (111.8 cm) 47" (119.4 cm) 47" (119.4 cm) K Recommended Cutout Location from Floor 131ø4" (33.7 cm) 12" (30.5 cm) 12" (30.5 cm) Continue to Section 3 for DWO with Pedestal. Otherwise, continue to Section 4. 31-10965-1 03-14 GE 2 D CUTOUT FOR DOUBLE OVENS (with Upper Microwave Oven) NOTE: If the cabinet does not have a front frame and the sides are less than ¾" (1.9 cm) thick, shim both sides equally to establish the cutout width. 2 E SECURING UPPER MICROWAVE/ADVANTIUM OVEN TO CABINET For double oven with microwave or Advantium upper ovens. Secure a wooden cleat to side of cabinet so that the upper oven can be secured to the cleat with provided screws 27" Cabinet requirements • No shims (or cleats) required when cabinet is in minimum width condition. • If cabinet is at maximum width condition, add wood shims to bring cabinet to minimum condition. 6.375" 30" Cabinet requirements • No shims (or cleats) required when cabinet is in minimum 27.5" width condition. • If cabinet is at maximum width condition, fix the wood cleats as shown in illustration. Wood Cleats 1.5" 3.0" Cleat locations on 30" cabinet with maximum cutout condition 3 PEDESTAL RAIL INSTALLATION (30" DOUBLE OVENS ONLY) A. Place one pedestal rail on each cabinet runner or centered on opposite side of solid cabinet bottom flush with side of cabinet opening. Locate each rail so that front of rail is behind front cabinet opening. B. Drill pilot holes and attach rails to runner or bottom of cabinet with provided hardware. Dim. Description A Cabinet Width B Cutout Width C Cutout Height D Overlap of Oven Over Side Edges of Cutout E Clearance to Adjacent Corners, Drawers, Walls, etc., When Door Is Open F Overlap of Oven Top of Cutout G Overlap of Oven Bottom of Cutout H Junction Box Location 27" Oven with Microwave 27" (68.6 cm) 25" (63.5 cm) min. 251ø4" (64.1 cm) max. 411ø8" (104.5 cm) min. 411ø4" (104.8 cm) max. 1" (2.5 cm) 23" (58.4 cm) min. 1" (2.5 cm) min. 1" (2.5 cm) min. 83ø4" (22.2 cm) max. right side only Continue to Section 4. 30" Oven with Microwave 30" (76.2 cm) 281ø2" (72.4 cm) min. 285ø8" (72.7 cm) max. 423ø16" (107.2 cm) min. 421ø4" (107.3 cm) max. 11ø16" (1.75 cm) 23" (58.4 cm) 1" (2.5 cm) min. 11ø4" (3.2 cm) 91ø2" (24.1 cm) max. right side only 2 F CUTOUT FOR INSTALLATION OVER A WARMING DRAWER NOTE: Install the oven only with specific models listed on the label located on top of the oven. NOTE: Additional clearances between cutouts may be required. Check to be sure the oven supports above the Warming Drawer location do not obstruct the required interior depth and height. When installing a Warming Drawer below a single or double oven, a separate 120V, 60 HZ, properly grounded receptacle must be installed. Refer to installation instructions packed with the Warming Drawer for specific installation requirements. Anti-Tip Block Against Rear Wall Per Warming Drawer Requirement 2" (5.1 cm) Min. Per Warming Drawer Requirement Continue to Section 4 4 A DOOR REMOVAL (RECOMMENDED) NOTE: Door removal is not a requirement for installation of the product but is an added convenience. To remove the door: A. Open the oven door as far as it will go. Hinge Bracket B. Remove hinge bracket from front frame and set aside. The hinge bracket must be replaced for proper door functionality when door is reinstalled. C. Push both hinge locks down toward the door frame to the unlocked position. This may require a flat-blade screwdriver. DO NOT LIFT THE DOOR BY THE HANDLE! D. Place hands on both sides of the door and close the oven door to the removal position (approximately 1"-2" [2.5 cm-5.1 cm] from the closed position). E. Lift the door up and out until the hinge arms clear the slots. NOTE: The oven door is very heavy. Be sure you have a firm grip before lifting the oven door off the hinges. Use caution once the door is removed. Do not lay the door on its handle. This could cause dents or scratches. Hinge Unlocked Position Hinge Slot Hinge Arm Hinge Clears Slot