GE GTM18GBEES Use and Care Manual - Page 5

About storage drawer and cover removal., About the automatic icemaker - refrigerator

Page 5 highlights

About storage drawer and cover removal. GEAppliances.com Not all features are on all models. Adjustable Humidity Drawer (on some models) Slide the control all the way to the HIGH setting to provide high humidity recommended for most vegetables. Slide the control all the way to the LOW setting to provide lower humidity levels recommended for most fruits. Drawer and Cover Removal Drawers can be removed easily by grasping the sides and lifting up slightly while pulling drawers past the stop location. To remove the cover,OLIWLWRȺLWVVXSSRUWV pull it forward, tilt it and take it out. Twin Drawer Shelf To remove: Remove the drawers. Reach in, push the front of glass cover up, and at the same time, pull it forward as far as it will come. Tilt it and take it out. Avoid cleaning the cold glass cover with hot water because the extreme WHPSHUDWXUHGLȺHUHQFHPD\FDXVHLWWREUHDN Remove the drawer frame. (Always remove the glass cover before you take out the drawer frame.) /LIWWKHIUDPHRȺWKHVXSSRUWVDWHDFKVLGHDQG back, pull it forward, tilt it and take it out. To replace: Lower the frame until it rests on the supports at each side and back. Replace the glass cover, pushing its rear HGJH¿UPO\LQWRWKHUHDUIUDPHFKDQQHODQG gently lowering the front into place. Replace the drawers. About the automatic icemaker A newly-installed refrigerator may take 12-24 hours to begin making ice. Icemaker ON OFF Feeler Arm Power Switch Feeler Arm in the STOP Feeler Arm in the (up) position ON (down) position Automatic Icemaker (on some models). The icemaker will produce approximately 70-100 cubes. in a 24-hour period, depending on the freezer compartment temperature, room temperature, number of door openings and other use conditions. If the refrigerator is operated before the water connection is made to the icemaker, set the switch OFF or move the feeler arm to the STOP (up) position. When the refrigerator has been connected to the water supply, set the switch ON position or move the feeler arm to the ON (down) position. 7KHLFHPDNHUZLOO¿OOZLWKZDWHUZKHQLWFRROVWR 15°F. A newly-installed refrigerator may take 12 to 24 hours to begin making ice cubes. Once the icemaker starts to make ice, it may take XSWRKRXUVWR¿OOWKHELQGHSHQGLQJRQWKH temperature settings and number of door openings. You will hear a buzzing sound each time the LFHPDNHU¿OOVZLWKZDWHU 7KURZDZD\WKH¿UVWIHZEDWFKHVRILFHWRDOORZ the water line to clear. Be sure nothing interferes with the sweep of the feeler arm. :KHQWKHELQ¿OOVWRWKHOHYHORIWKHIHHOHUDUPWKH icemaker will stop producing ice. It is normal for several cubes to be joined together. If ice is not used frequently, old ice cubes will become cloudy, taste stale, shrink or fuse together. Icemaker accessory kit: If your refrigerator did not already come equipped with an automatic icemaker, an icemaker accessory kit is available at extra cost. &KHFNWKHEDFNRIWKHUHIULJHUDWRUIRUWKHVSHFL¿F icemaker kit needed for your model. 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

About storage drawer and cover removal.
GEAppliances.com
Not all features are on all models.
Twin Drawer Shelf
To remove:
Remove the drawers.
Reach in, push the front of glass cover up,
and at the same time, pull it forward as far
as it will come.
Tilt it and take it out. Avoid cleaning the cold
glass cover with hot water because the extreme
Remove the drawer frame. (Always remove
the glass cover before you take out the
drawer frame.)
back, pull it forward, tilt it and take it out.
To replace:
Lower the frame until it rests on the
supports at each side and back.
Replace the glass cover, pushing its rear
gently lowering the front into place.
Replace the drawers.
Drawer and Cover Removal
Drawers can be removed easily by grasping
the sides and lifting up slightly while pulling
drawers past the
stop
location.
To remove the cover,
pull it forward, tilt it and take it out.
Adjustable Humidity Drawer
(on some models)
Slide the control all the way to the
HIGH
setting to provide high humidity
recommended for most vegetables.
Slide the control all the way to the
LOW
setting to provide lower humidity levels
recommended for most fruits.
Automatic Icemaker
(on some models).
The icemaker will produce approximately
70-100 cubes. in a 24-hour period, depending
on the freezer compartment temperature, room
temperature, number of door openings and other
use conditions.
If the refrigerator is operated before the water
connection is made to the icemaker, set the
switch
OFF
or move the feeler arm to the
STOP
(up) position.
When the refrigerator has been connected to the
water supply, set the switch
ON
position or move
the feeler arm to the
ON
(down) position.
15°F. A newly-installed refrigerator may take 12 to
24 hours to begin making ice cubes.
Once the icemaker starts to make ice, it may take
temperature settings and number of door openings.
You will hear a buzzing sound each time the
the water line to clear.
Be sure nothing interferes with the sweep of the
feeler arm.
icemaker will stop producing ice.
It is normal for several cubes to be joined
together.
If ice is not used frequently, old ice cubes will
become cloudy, taste stale, shrink or fuse together.
Icemaker accessory kit:
If your refrigerator did not already come equipped
with an automatic icemaker, an icemaker
accessory kit is available at extra cost.
icemaker kit needed for your mode
l.
About the automatic icemaker
A newly-installed refrigerator may take 12–24 hours to begin making ice.
Feeler Arm
in the
STOP
(up) position
Feeler Arm in the
ON
(down) position
ON
OFF
Icemaker
Feeler Arm
Power Switch
5