GE JGP933 Installation Instructions
GE JGP933 - Profile 30" Gas Cooktop Manual
 |
View all GE JGP933 manuals
Add to My Manuals
Save this manual to your list of manuals |
GE JGP933 manual content summary:
- GE JGP933 | Installation Instructions - Page 1
Installation 30″ Sealed Gas Cooktop Instructions JGP328, JGP330, JGP933, JGP940, JGP945 Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca IN THE COMMONWEALTH OF MASSACHUSETTS: • This product must - GE JGP933 | Installation Instructions - Page 2
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS electrical requirEments This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having - GE JGP933 | Installation Instructions - Page 3
tools and materials you need before starting the installation of the cooktop. E Your home must provide the adequate electrical service needed to safely and properly use your cooktop. (Refer to section on electrical requirements.) F When installing your cooktop in your home, make sure all local codes - GE JGP933 | Installation Instructions - Page 4
clearance from cutout to side wall on the left of the unit NOTE: All gas cooktop models require 7/16″ free area below cooktop height to combustible material. 2 Overall cooktop dimensions 30″ Cooktop 21″ (21-1/2″ Max. for Glass Top models) 3″ 19-3/8″ 28-1/4″ 4 Recommended Gas Supply Location - GE JGP933 | Installation Instructions - Page 5
Installation Instructions Installing the Cooktop Unit 1 Locate Electrical Outlet and gas Shut-Off Valve beneath Cabinet NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS UNIT. Shut Off Valve Electrical Outlet 12″ Below Countertop Install a manual shut-off valve in the gas line in an easily - GE JGP933 | Installation Instructions - Page 6
Regulator NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS COOKTOP. WARNING: Never reuse old flexible connectors. The use of old flexible connectors can cause gas leaks and personal injury. Always use new flexible connectors when installing a gas appliance. Screw a section of pipe onto the inlet - GE JGP933 | Installation Instructions - Page 7
cooktop from the gas supply piping system by closing its individual shut-off valve during any pressure testing of the gas supply system at test pressures equal to or less than 1/2 psig (3.5 kPa). 6 INSTALLATION OVER BUILT-IN OVEN See built-in oven installation for complete installation instructions - GE JGP933 | Installation Instructions - Page 8
(Please read carefully) FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED. 2 electrical supply and outlet An adequate electrical supply and outlet must be used to operate the electrical parts of your cooktop. A The power cord of this appliance is equipped with a 3-prong (grounding) plug - GE JGP933 | Installation Instructions - Page 9
Installation Instructions 4 Usage situations where appliance power cord will be disconnected infrequently For 15 amp Attaching the adaptor ground terminal to the wall receptacle cover screw does not ground the appliance unless the screw is metal, and not insulated, and the wall receptacle is - GE JGP933 | Installation Instructions - Page 10
Installation Instructions Cooktop Burners 1 Assembling the Cooktop Burners The electrode of the spark igniter is exposed. Be careful not to push any cooktop controls while the top of the burner is removed. Do not remove the top or touch the electrode of any burner while another burner is - GE JGP933 | Installation Instructions - Page 11
Installation Instructions 2 Check Igniters Operation of the electric igniters should be checked after the cooktop and supply line have been carefully checked for leaks and the cooktop has been connected to the electrical power. On models so equipped, check to be sure the cooktop is in the UNLOCKED - GE JGP933 | Installation Instructions - Page 12
Installation Instructions Operation Checklist A Make sure all controls are left in the OFF position. Check to be sure the cooktop is in the UNLOCKED position (on models so equipped). B Make sure the flow of air to and from the cooktop is unobstructed. C The serial plate for your cooktop is located - GE JGP933 | Installation Instructions - Page 13
in Step 2. 13 2 adjust your cooktop for use with LP gas A Disconnect all electrical power, at the main circuit breaker or fuse box. B Shut off the gas supply to the cooktop by closing the manual shut-off valve. C Adjust the pressure regulator, by the following instructions: • Unscrew the cap - GE JGP933 | Installation Instructions - Page 14
Installation Instructions Making the LP Conversion (CONT.) 3 Change Cooktop Burner Orifices A Remove the top grates, burner caps, and burner heads. Remove This Assembly B Remove the spark igniters from the burner base (if required to access the orifices). Using a No. 15 "Torx" head driver - GE JGP933 | Installation Instructions - Page 15
Installation Instructions 3 Change Cooktop Burner Orifices (CONT.) D Locate the LP/Propane orifices shipped inside the literature package. They will have a digit number and the letter "L" on the side. (Important: Save the orifices removed from the appliance for future use.) Each orifice will show a - GE JGP933 | Installation Instructions - Page 16
blue in color with some yellow tipping at the ends of the flame. Foreign particles in the gas line may cause an orange flame at first, but this will soon disappear. NOTE: For the 18,000 BTU/HR burner (on some models) the cooktop burner knob should be turned to the setting before the lowest setting - GE JGP933 | Installation Instructions - Page 17
fournisseur de gaz à l'aide du téléphone d'un voisin. Suivez les instructions de votre fournisseur de gaz. • Si vous ne pouvez pas entrer en contact avec votre fournisseur de gaz, appelez les pompiers. L'installation et le service de votre table de cuisson doivent être faits par un installateur - GE JGP933 | Installation Instructions - Page 18
Instructions d'installation INSTRUCTIONS IMPORTANTES DE SÉCURITÉ La conception de votre table de cuisson a été approuvé par l'ACNOR International. Vous trouverez des précautions à prendre en matière de sécurité dans votre Guide d'utilisation et de soins. Lisez-les attentivement. • L 'installation - GE JGP933 | Installation Instructions - Page 19
de commencer à l'installer. Documentation Boîtes de grille Emballage en mousse Table de cuisson C Enlevez les instructions d'installation de la trousse de armoires autour de la table de cuisson puissent supporter la chaleur [pouvant atteindre 93°C (200°F)] produite par la table de cuisson. 3 - GE JGP933 | Installation Instructions - Page 20
Instructions d'installation PRÉPARATION DE L'OUVERTURE 1 Vous devez respecter les dégagements minimaux suivant Profondeur max de 33 cm (13″) des armoires en surplomb non protégées Dégagement min. de 15 3c3m/4 M(I6N.″) découpage au mur de côté à droite de l'appareil Dégagement min. de 76 cm (30 - GE JGP933 | Installation Instructions - Page 21
Instructions d'installation Installation LA UNITÉ de la table de cuisson 1 Placez la prise d'alimentation électrique et le robinet d'alimentation de gaz au-dessous de l'armoire N'utilisez jamais des raccords usagés pour installer cet appareil. Robinet d'alimentation Prise électrique 30 cm (12″) - GE JGP933 | Installation Instructions - Page 22
Instructions d'installation Installation-BRANCHEMENT DU GAZ 1 Fournissez un bon approvisionnement en gaz Cette table de cuisson est conçue pour fonctionner au gaz naturel à une pression de tubulure d' - GE JGP933 | Installation Instructions - Page 23
alimentation en gaz à des pressions de test égales ou inférieures à 1/2 psig (3,5 kPa). 6 Installation sur un four encastré Consultez l'installation du four encastré pour y trouver les instructions d'installation. Coude de 90° Côtés de l'armoire 5 po. depuis le comptoir jusqu'au centre du trou de - GE JGP933 | Installation Instructions - Page 24
Instructions d'installation Installation-Raccords Électriques AVERTISSEMENT - Débranchez tout courant électrique au niveau du disjoncteur de la maison ou de la boîte à fusibles avant d'installer. 1 RALLONGES À cause du danger qu'elles font courir dans certaines conditions, nous vous recommandons - GE JGP933 | Installation Instructions - Page 25
Instructions d'installation Installation-Raccords Électriques (SUITE) 4 Situation d'utilisation où le cordon d'alimentation d'un appareil électroménager est infréquemment débranché Pour un circuit électrique de 15 ampéres uniquement. N' - GE JGP933 | Installation Instructions - Page 26
Instructions d'installation BrÛleurs de la table de cuisson 1 Assemblez les brûleurs de la table de cuisson L'électrode de l'allumeur est exposée. Faites attention de ne - GE JGP933 | Installation Instructions - Page 27
Instructions d'installation 2 Vérifiez les allumeurs Vous devez vérifier le fonctionnement des allumeurs électriques après vous être soigneusement assuré que la table de cuisson et la ligne d'approvisionnement n' - GE JGP933 | Installation Instructions - Page 28
Instructions d'installation BrÛ la catégorie de carburant et la pression de votre table de cuisson au départ de la fabrique. D Quand vous commandez des pièces. indiquez toujours le suivi toutes les instructions de ce guide. Cela assure une bonne utilisation sécuritaire de la table de cuisson. 12 - GE JGP933 | Installation Instructions - Page 29
Instructions d'installation Conversion au gaz propane (LP) 1 Renseignements relatifs à la sé la table de cuisson dans la documentation jointe au régulateur. ATTENTION : La table de cuisson, au départ de l'usine, est réglée pour le gaz naturel. Si vous désirez utiliser votre table de cuisson avec - GE JGP933 | Installation Instructions - Page 30
Instructions d'installation Conversion au gaz propane (LP) (SUITE) 3 Changez les diaphragmes des brûleurs de en passant par le trou de la table de cuisson. Allumeur Base de brûleur Brûleur de 18000 BTU (sur certains modèles) Base de brûleur Capuchon de brûleur Tête de brûleur 3 Changez les - GE JGP933 | Installation Instructions - Page 31
Instructions d'installation TU/HR (sur cIeIIrtaines modèXles) Le brûleur de 18 000 BTU/HR a deux diaphragmes qui portent des marques de côté seulement (consultez la diaphragmes pour gaz naturel sur le support et fixez à nouveau le support et la feuille d'instructions au régulateur de pression à l' - GE JGP933 | Installation Instructions - Page 32
Instructions d'installation Conversion au gaz propane (LP) (SUITE) 4 Ajustez les flammes des brûleurs A orange au début, mais cette couleur doit disparaître rapidement. NOTE : Pour le brûleur de 18 000 BTU/HR (sur certains modèles), vous devez tourner le bouton du brûleur de la table de cuisson à
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
 |
 |
1
31-10613-5
(10-10 GE)
Before You Begin
Read these instructions completely
and carefully.
•
iMPorTAnT
—
Save these instructions
for local inspector’s use.
•
iMPorTAnT
—
Observe all governing
codes and ordinances.
•
Note to Installer – Be sure to leave these
instructions with the Consumer.
•
Note to Consumer – Keep these instructions for
future reference.
•
Product failure due to improper installation is not
covered under the Warranty.
WArning
—
This appliance must be
properly grounded.
•
iMPorTAnT
—
Leak testing of the
appliance shall be conducted according to the
manufacturer’s instructions.
•
Proper installation is the responsibility of the
installer and product failure due to improper
installation is NOT covered under warranty.
in THe CoMMonWeALTH of
MASSACHuSeTTS:
• This product must be installed by a licensed
plumber or gas fitter.
• When using ball-type gas shut-off valves, they
shall be the T-handle type.
• A flexible gas connector, when used, must not
exceed 3 feet.
Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: ge.com
In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca
iNstallatION
30
″
SEalEd gas COOktOp
iNstRUctIONs
JGP328, JGP330, JGP933,
JGP940, JGP945
for Your SAfeTY:
WArning
—
If the information
in this manual is not followed exactly, a fire,
explosion or gas leak may result causing property
damage, personal injury or death.
Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance!
WHAT To Do if You SMeLL
gAS:
• Do not try to light any appliance. Do not touch
any electrical switch; do not use any phone in
your building.
• Immediately call your gas supplier from a
neighbor’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire
department.
Installation and service must be performed
by a qualified installer, service agency or
the gas supplier.
This cooktop has been design certified
by CSA International. You’ll find safety precautions
in your Owner’s Manual.
Read them carefully.
• Installation of this cooktop must conform with
local codes or in the absence of local codes with
the National Fuel Gas Code, ANSI Z223.1/NFPA
54–Latest edition.
• Be sure your cooktop is installed properly by a
qualified installer or service technician.
• To eliminate reaching over surface burners,
cabinet storage above burner should be avoided.
• Do not install the unit near an outside door or
where a draft may affect its use.
WArning
—
Disconnect all electrical
power at the main circuit breaker
or fuse box before installing.