GE JTP48BFBB User Manual - Page 17

How to Delay the Start of Cleaning, After a Clean Cycle, ge.com, SELF CLEAN STD/LOW, DELAY START

Get GE JTP48BFBB PDF manuals and user guides View all GE JTP48BFBB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Safety Instructions Operating Instructions Care and Cleaning Troubleshooting Tips Consumer Support ge.com The oven door must be closed and all controls must be set correctly for the cycle to work properly. How to Delay the Start of Cleaning Press the SELF CLEAN STD/LOW pad once for a 4-hour clean time or twice for a 3-hour clean time. A 3-hour self-clean time is recommended for use when cleaning small, contained spills. A self-clean time of 4 hours or longer is recommended for a dirtier oven. If a time other than 4 hours or 3 hours is needed, use the HOUR and MIN + or - pads and enter the desired clean time. You can change the clean time to any time between 3 hours and 5 hours, depending on how dirty your oven is. Press the DELAY START pad. Using the HOUR and MIN + or - pads, enter the time of day you want the clean cycle to start. Press the START pad. The door locks automatically. The display will show the start time. It will not be possible to open the oven door until the temperature drops below the lock temperature and the LOCKED light goes off. When the LOCKED light goes off, you will be able to open the door. NOTE: On models with touch pad controls for both ovens, you can set a delay clean in both ovens at the same time. The second oven set will automatically delay the start of cleaning until the end of the first oven's clean cycle. To recall the start time of the second oven set, press the DELAY START pad on the controls for the second oven. After a Clean Cycle You may notice some white ash in the oven. Wipe it up with a damp cloth after the oven cools. If white spots remain, remove them with a soap-filled scouring pad and rinse thoroughly with a vinegar and water mixture. These deposits are usually a salt residue that cannot be removed by the clean cycle. If the oven is not clean after one clean cycle, repeat the cycle. s You cannot set the oven for cooking until the oven is cool enough for the door to unlock. s If the shelves become hard to slide, wipe the shelf supports with cooking oil. 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
17
Safety Instructions
Operating Instructions
Care and Cleaning
Troubleshooting Tips
Consumer Support
ge.com
The oven door must be closed and all controls must be set correctly for the cycle to work properly.
How to Delay the Start of Cleaning
Press the
SELF CLEAN STD/LOW
pad
once for a 4-hour clean time or
twice for a 3-hour clean time.
A 3-hour self-clean time is
recommended for use when
cleaning small, contained spills. A
self-clean time of 4 hours or longer
is recommended for a dirtier oven.
If a time other than 4 hours or
3 hours is needed, use the
HOUR
and
MIN +
or
–
pads and enter
the desired clean time.
You can change the clean time to any
time between 3 hours and 5 hours,
depending on how dirty your oven is.
Press the
DELAY START
pad.
Using the
HOUR
and
MIN +
or
–
pads, enter the time of day you want
the clean cycle to start.
Press the
START
pad.
The door locks automatically. The display
will show the start time. It will not be
possible to open the oven door until
the temperature drops below the lock
temperature and the
LOCKED
light
goes off.
When the
LOCKED
light goes off, you will
be able to open the door.
NOTE:
On models with touch pad controls for
both ovens, you can set a delay clean in both
ovens at the same time. The second oven set will
automatically delay the start of cleaning until the
end of the first oven’s clean cycle.
To recall the start time of the second oven set,
press the
DELAY START
pad on the controls for
the second oven.
After a Clean Cycle
You may notice some white ash in the
oven. Wipe it up with a damp cloth after
the oven cools.
If white spots remain, remove them with a
soap-filled scouring pad and rinse thoroughly with
a vinegar and water mixture.
These deposits are usually a salt
residue that cannot be removed by
the clean cycle.
If the oven is not clean after one clean
cycle, repeat the cycle.
■
You cannot set the oven for cooking
until the oven is cool enough for the
door to unlock.
■
If the shelves become hard to
slide, wipe the shelf supports with
cooking oil.